R (1) Open the access panel 196BB.

R  Subtask 29-13-45-860-053 
R  D. Aircraft Maintenance Configuration 
R  WARNING : OBEY THE HYDRAULIC SAFETY PROCEDURES._______ 
R  (1) Obey the hydraulic safety procedures (Ref. TASK 29-00-00-910-002). 
R  (2) Make sure that the Yellow hydraulic system is depressurized and put 
R  it in the maintenance configuration. 
R  (Ref. TASK 29-00-00-864-001). 
R  (3) Depressurize the reservoir of the Yellow hydraulic system (Ref. TASK 
R  29-14-00-614-001). 
R  (4) Disconnect the isolation coupling of the Power Transfer Unit (PTU) 
R  (Ref. TASK 29-23-00-860-001). 
R  (5) Put the CONTAINER 1 L (1/4 USGAL) below the filter to collect the 
R  unwanted hydraulic fluid. 
R  4. Procedure_________ 
R  Subtask 29-13-45-020-051 
R  A. Removal of the Clogging Indicator 
R  (1) Loosen and remove the clogging indicator (4) from the filter head 
R  (1). 
R  (2) Remove and discard the packings (7) from the clogging indicator (4). 
R  (3) Remove and retain the ring (6) from the clogging indicator (4). 
R  Subtask 29-13-45-560-051 
R  B. Preparation for Installation 
R  (1) Put the ring (6) on the clogging indicator (4). 
R  (2) Lubricate the new packings (7) with the HYDRAULIC FLUIDS (Material 
R  No. 02-003) and install them on the clogging indicator (4). 
R  (3) Lubricate the threads of the clogging indicator (4) with the 
R  HYDRAULIC FLUIDS (Material No. 02-003).

R  Subtask 29-13-45-420-051 
R  C. Installation of the Clogging Indicator 
R  (1) Clean the component interface and/or the adjacent area. 
R  (2) Do an inspection of the component interface and/or the adjacent area. 
R  (3) Install the new clogging indicator (4) in the filter head (1). 
R  Subtask 29-13-45-942-052 
R  D. Safety Precautions 
R  (1) Remove the warning notice(s). 
R  Subtask 29-13-45-865-053 
R  E. Remove the safety clip(s) and the tag(s) and close this(these) circuit 
R  breaker(s): 
R  3801GX, 3802GX, 3803GX. 
R  Subtask 29-13-45-790-051 
R  F. Test of the Filter Assembly 
R  (1) Pressurize the reservoir of the Yellow hydraulic system (Ref. TASK 
R  29-14-00-614-002). 
R  (2) Pressurize the Yellow hydraulic system (Ref. TASK 29-10-00-863-002). 
R  (3) Make sure that the clogging indicator stays in. 
R  (4) Make sure that no hydraulic fluid comes out of the filter assembly. 
R  (5) Depressurize the Yellow hydraulic system (Ref. TASK 29-10-00-864-
R  002).

R  5. Close-up________ 
R  Subtask 29-13-45-860-054 
R  A. Put the aircraft back to the serviceable condition. 
R  (1) Make sure that the fluid level in the Yellow reservoir is correct. 
R  Add fluid as necessary (Ref. TASK 12-12-29-611-001). 
R  (2) Remove the container from below the filter. 
R  (3) Connect the PTU isolation coupling (Ref. TASK 29-23-00-860-002). 
R  (4) Make sure that the work area is clean and clear of tool(s) and other 
R  items. 
R  Subtask 29-13-45-410-051 
R  B. Close Access 
R  (1) Close the access panel 196BB.

 SLIDE - COMPENSATED (3010GM) - REMOVAL/INSTALLATION
___________________________________________________
 TASK 29-13-47-000-001
 Removal of the Compensated Slide (3010GM)
 WARNING : PUT THE SAFETY DEVICES AND THE WARNING NOTICES IN POSITION BEFORE YOU
_______ START A TASK ON OR NEAR:
 -
THE FLIGHT CONTROLS

 -
THE FLIGHT CONTROL SURFACES

 -
THE LANDING GEAR AND THE RELATED DOORS

 -COMPONENTS THAT MOVE.
 WARNING : MAKE SURE THAT THE GROUND SAFETY-LOCKS ARE IN POSITION ON THE LANDING
_______ GEAR.
 1. Reason for the Job
__________________
 Self Explanatory
 2. Job Set-up Information
______________________
 A. Fixtures, Tools, Test and Support Equipment
 -------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM HYDRAULIC POWER 液壓4(59)