曝光臺 注意防騙 網曝天貓店富美金盛家居專營店坑蒙拐騙欺詐消費者

R  damaged flats. the damaged end-fittings keep the correct torque 
R  can keep the correct value, replace the 
R  torque value. hose-tube assembly 
R  (Ref. TASK 29-13-49-000-
R  005) and (Ref. TASK 29-13-
R  49-400-005). 
R  6. Examine the pressure relief-valve tube-assembly, look for: 
R  A. Cracks, splits or None permitted. Replace the tube assembly 
R  kinks. (Ref. TASK 29-13-49-000-
R  006) and (Ref. TASK 29-13-
R  49-400-006). 
R  B. Wrinkles in bends. Maximum depth cannot be If wrinkles are more than 
R  more than 0.0075 in. the allowable limits, 
R  (0.1905 mm). replace the tube assembly 
R  (Ref. TASK 29-13-49-000-
R  006) and (Ref. TASK 29-13-
R  49-400-006).

 

 -------------------------------------------------------------------------------INSPECT/CHECK MAXIMUM REMARKS SERVICEABLE LIMITS -------------------------------------------------------------------------------
R  C. Dents. 
R 
R 
R 
R 
R 
R 
R 
R 
R  D. Flat areas. 
R 
R 
R 
R 
R 
R 
R 
R 
R  E. Nicks, scratch 
R  chafing or scores 
R  in bends. 
R 
R 
R 
R  F. End-fitting thread 
R  damage. 
R 
R 
R 
R 
R  G. End-fitting 
R  damaged flats. 
R 
R 
R 
R 

Two per linear foot (305 mm). Provided depth does not exceed 0.025 in.
(0.635 mm) (10 percent of tube O.D.) and radius is not less than 0.04 in. (1.016 mm) (less than two times the wall thickness).
Maximum flat area can not be more than 0.5 in.
(12.7 mm) (not more than three times the tube O.D). The contour change cannot be more than 0.05 in. (1.27 mm) (20 percent of the tube O.D.).
Maximum depth cannot be more than 0.002 (0.0508 mm) (not more than 10 percent of wall thickness).
Damage is permitted if the threads that are good are not reduced by more than one thread.
Damage is permitted if the damaged end-fittings can keep the correct torque value.
If the damage is more than the allowable limits, replace the tube assembly (Ref. TASK 29-13-49-000-006) and (Ref. TASK 29-13-49-400-006).
If the flat areas are more than the allowable limits, replace the tube assembly (Ref. TASK 29-13-49-000-006) and (Ref. TASK 29-13-49-400-006).
If the damage is more than the allowable limits, replace the tube assembly (Ref. TASK 29-13-49-000-006) and (Ref. TASK 29-13-49-400-006).
If the damage is more than the allowable limits, replace the tube assembly (Ref. TASK 29-13-49-000-006) and (Ref. TASK 29-13-49-400-006).
If the end-fittings cannot keep the correct torque value, replace the tube assembly (Ref. TASK 29-13-49-000-006) and (Ref. TASK 29-13-49-400-006).

 5. Close-up
________ Subtask 29-13-49-410-070
 A. Close Access
 (1)
 Make sure that the work area is clean and clear of tool(s) and other items.

 (2)
 Close the fan-cowl doors:
 FOR 1000EM2

 -447AL, 448AR (Ref. TASK 71-13-00-410-040).

 (3)
 Remove the access platform(s).

 (4)
 Remove the warning notice(s). Subtask 29-13-49-865-066

 B.
 Remove the safety clip(s) and the tag(s) and close this(these) circuit breaker(s): 3700GD

 

 PUMP - ENGINE (3030GD) - REMOVAL/INSTALLATION
_____________________________________________ TASK 29-13-51-000-004 R Removal of the Yellow Engine Pump (3030GD) WARNING : OBEY THE HYDRAULIC SAFETY PROCEDURES.
_______
 WARNING : DO NOT TOUCH THE HYDRAULIC SYSTEM COMPONENTS FOR A SHORT TIME AFTER

_______ THE ENGINE IS SHUTDOWN. THE ENGINE COMPONENTS STAY HOT FOR SOME TIME AND CAN CAUSE INJURY.
 CAUTION : DO NOT LET HYDRAULIC FLUID FALL ON THE ENGINE. UNWANTED HYDRAULIC
_______ FLUID MUST BE REMOVED IMMEDIATELY WITH A CLEAN LINT FREE CLOTH. THE FLUID CAN CAUSE DAMAGE TO THE SURFACE PROTECTION AND TO SOME PARTS.
 1.
 Reason for the Job

__________________
 Self Explanatory

 2.
 Job Set-up Information

______________________
 A. Fixtures, Tools, Test and Support Equipment
 -------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM HYDRAULIC POWER 液壓4(89)