(2)
Loosely connect the pressure hose/tube (20) to the fluid disconnect panel. Do not TORQUE the coupling nut at this time.
(3)
Attach the pressure hose/tube (20) to the higher bracket with the clamp (15), the bolt (5) and the washer (10). Do not TORQUE the bolt at this time.
(4)
Loosely connect the pressure switch to the tee-fitting on the pressure hose/tube (20). Do not TORQUE the coupling nut at this time.
(5)
Attach the pressure hose/tube (20) to the two channels with the clamps (15), the bolts (5) and the washers (10). Do not TORQUE the bolts at this time.
(6)
Attach the pressure hose/tube (20) to the lower bracket with the clamps (15), the bolts (5) and the washer (10). Do not TORQUE the bolt at this time.
(7)
Install the center mount clamp (40) as follows:
(a)
Remove the bolt (25), the washer (30) and the nut (35) from the band on the center mount clamp (40).
(b)
Open the band on the clamp (40) and put the pressure hose/tube
(10) into its hole in the insert.
(c)
Put the band on the insert and install the bolt (25), the washer
(30) and the nut (35).
(d)
Make sure that the center mount clamp (40) is installed at a distance of 338 mm (13.3070 in.) below the flange of the pressure hose/tube.
(e)
TORQUE the nut (35) to between 0.23 and 0.28 m.daN (20.35 and
24.77 lbf.in).
(8)
Loosely connect the pressure hose/tube (20) to the union on the hydraulic pump. Do not TORQUE the nut at this time.
(9)
Make sure that the pressure hose/tube (20) is in the correct position on the engine.
NOTE : Use a second wrench to hold the fittings when you TORQUE the
____
coupling nuts. This prevents damage to the hose/tube
assemblies.
(10)
TORQUE the coupling nuts on the two ends of the pressure hose/tube
(20) to between 9.66 and 10.6 m.daN (71.23 and 78.17 lbf.ft). TORQUE the coupling nut on the pressure switch tube to between 2.42 and 2.76 m.daN (17.84 and 20.35 lbf.ft).
(11)
TORQUE the bolts (5) to between 0.23 and 0.28 m.daN (20.35 and 24.77 lbf.in).
Subtask 29-13-49-710-060
B. Operational Test
(1)
Pressurize the Yellow hydraulic reservoir (Ref. TASK 29-14-00-614-002).
(2)
Do an operational test of the Yellow hydraulic system (Ref. TASK 29-13-00-710-002).
(3)
During the dry motoring of the engine 2, make sure that there are no leaks from the suction hose/tube.
(4)
Make sure that the level of the hydraulic fluid in the Yellow reservoir is correct. If necessary, fill the reservoir (Ref. TASK 12-12-29-611-001) or (Ref. TASK 12-12-29-611-002).
5. Close-up
________
Subtask 29-13-49-410-063
A. Close Access
(1)
Remove the container.
(2)
Remove the warning notice(s).
(3)
Remove the access platform(s).
(4)
Make sure that the work area is clean and clear of tool(s) and other items.
R (5) Close the left fan-cowl door (Ref. TASK 71-13-00-410-040): FOR 1000EM2 close the door 447AL.
(6) Close the door 195BB.
TASK 29-13-49-000-003
Removal of the Top Case Drain Hose/Tube Assembly
WARNING : OBEY THE HYDRAULIC SAFETY PROCEDURES.
_______
WARNING : DO NOT TOUCH THE HYDRAULIC SYSTEM COMPONENTS FOR A SHORT TIME AFTER
_______ THE ENGINE IS SHUTDOWN. THE ENGINE COMPONENTS STAY HOT FOR SOME TIME AND CAN CAUSE INJURY.
CAUTION : DO NOT LET HYDRAULIC FLUID FALL ON THE ENGINE. UNWANTED HYDRAULIC
_______ FLUID MUST BE REMOVED IMMEDIATELY WITH A CLEAN LINT FREE CLOTH. THE FLUID CAN CAUSE DAMAGE TO THE SURFACE PROTECTION AND TO SOME PARTS.
1. Reason for the Job
__________________
Self Explanatory
2. Job Set-up Information
______________________
A. Fixtures, Tools, Test and Support Equipment
-------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
No specific circuit breaker(s) safety clip(s)
No specific protective covers
No specific warning notice(s)
No specific wrench
No specific access platform 1.50 m (4 ft. 11 in.)
No specific container 5 l (1.3208 USgal)
B. Referenced Information
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM HYDRAULIC POWER 液壓4(71)
