3. Job Set-up__________
 Subtask 29-13-51-860-056
 A. Aircraft Maintenance Configuration 
R R  (1) Make sure that the aircraft electrical circuits are energized (Ref. TASK 24-41-00-861-002). 
R  (2) Make sure that the Yellow hydraulic system is depressurized (Ref. TASK 29-24-00-864-001). 
R  (3) Make sure that the Yellow hydraulic reservoir is depressurized (Ref. TASK 29-14-00-614-001). 
R R  (4) Make sure that the warning notice(s) is (are) in position to tell persons not to pressurize the Yellow hydraulic system: - on the ground service panel 198CB. 
R R  (5) Make sure that the warning notice(s) is (are) in position on the access door 195BB to tell persons not to pressurize the Yellow hydraulic reservoir. 
R  (6) Make sure that an access platform is in position at the engine. 
R R  (7) Make sure that the left fan cowl door 447AL is open (Ref. TASK 71-13-00-010-040).
 Subtask 29-13-51-941-055
 B. Safety Precautions
 (1) On the center pedestal, on the ENG panel 115VU: - make sure that the warning notice(s) is (are) in position to tell persons not to start the engine.
 (2) Make sure that the engine 1(2) shutdown occurred not less than 5 minutes before you do this procedure.
R  (3) Make sure that the warning notice(s) is (are) in position to tell persons not to pressurize the Yellow hydraulic system: - in the cockpit, on the HYD section of the panel 40VU.

R (4) On the maintenance panel 50VU:
 -make sure that the ON legend of the ENG/FADEC GND PWR/1(2) R pushbutton switch is off R R - make sure that the warning notice(s) is (are) in position to tell R persons not to energize the FADEC 1(2).
R (5) Make sure that a container is below the Yellow engine pump to collect R the remaining fluid.
 Subtask 29-13-51-865-057
 C. Make sure that this(these) circuit breaker(s) is(are) open, safetied and tagged
 -------------------------------------------------------------------------------PANEL DESIGNATION IDENT. LOCATION -------------------------------------------------------------------------------
121VU HYDRAULIC/Y HYD/PUMP ENG2/MONG
121VU HYDRAULIC/Y HYD/PUMP ENG2/CTL
4. Procedure
_________ R (Ref. Fig. 401/TASK 29-13-51-991-300) Subtask 29-13-51-640-053
 A. Preparation before Installation
3700GD Q37
3701GD Q36

 (1) Lubricate the new packing (40) with HYDRAULIC FLUIDS (Material No.
 02-003). Install the packing on the splined drive shaft of the pump. R (2) Remove the blanking plugs from the engine pump (35) and the gearbox R mount pad. R
R (3) Put a new gasket (45) on the gearbox mount pad.
 Subtask 29-13-51-420-055 R B. Installation of the Yellow Engine Pump R (1) Install the pump (35) as follows:
 (a) Put the pump (35) in position on the gearbox mount pad with the nuts (50) through the large holes in the pump flange.

 (b) Turn the pump (35) in a counterclockwise direction, until the studs on the mount pad are in the correct position. 
R R  (c) TORQUE the nuts (50) to between 260 and 320 lbf.in (2.93 and 3.61 m.daN).
 (2) Remove the protective covers from the union (15), the union/reducer (25) and (65).
 (3) Lubricate the new packing (30), packing (55), packing (60) with HYDRAULIC FLUIDS (Material No. 02-003).
 (4) Put the packing (60) on the union/reducer (65) and install the union/reducer in the pressure port of the pump (35). 
R R  (5) TORQUE the union/reducer (65) to between 1350 and 1450 lbf.in (15.25 and 16.38 m.daN).
 (6) Put the packing (55) on the union (15) and install the union in the suction port of the pump (35). 
R R  (7) TORQUE the union (15) to between 860 and 940 lbf.in (9.71 and 10.62 m.daN).
 (8) Put the packing (30) on the union/reducer (25) and install the union/reducer in the case drain port of the pump (35). 
R R  (9) TORQUE the union/reducer (25) to between 270 and 290 lbf.in (3.05 and 3.27 m.daN). 
R  (10) Connect the case drain hose (20) to the union/reducer (25). 
R R R  CAUTION : BE CAREFUL WHEN YOU INSTALL/CONNECT PARTS ON THE PUMP TO_______ MAKE SURE THAT THE HYDRAULIC FLUID DOES NOT FLOW OUT. THE PUMP IS FULL OF HYDRAULIC FLUID. 
R R  (11) TORQUE the case drain hose (20) coupling nut to between 270 and 300 lbf.in (3.05 and 3.39 m.daN). 
R R  NOTE : Use a second wrench to hold the union/reducer (25) when you____ torque the case drain hose coupling nut. 
R R  (12) Connect the adapter (70) to the union (15) in the pump (35) suction port. 
R  (13) Connect the suction hose (10) to the adapter (70).
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM HYDRAULIC POWER 液壓4(92)