曝光臺 注意防騙 網曝天貓店富美金盛家居專營店坑蒙拐騙欺詐消費者

lines from the toe brakes to the main wheel brake calipers are
plumbed through a parking brake valve. For normal operation, the
knob is pushed in. With the knob pushed in, poppets in the valve are
mechanically held open allowing normal brake operation. When the
handle is pulled out, the parking brake valve holds applied brake
pressure, locking the brakes. To apply the parking brake, set the
brakes with the rudder-pedal toe brakes, and then pull the PARK
BRAKE knob aft.
Revision A5
7-64 P/N 13772-001
Section 7 Cirrus Design
Airplane Description SR22
Figure 7-12
CALIPER
ASSEMBLY
CALIPER
ASSEMBLY
RUDDER
PEDAL(4)
SR22_FM07_1015
PARKING BRAKE
VALVE
PARKING
BRAKE
KNOB
MASTER CYLINDER(4)
RESERVOIR
MIL-H-5606
FLUID ONLY
ROTOR
(DISK)
ROTOR
(DISK)
Brake System
Revision A5
P/N 13772-001 7-65
Cirrus Design Section 7
SR22 Airplane Description
Electrical System
The airplane is equipped with a two-alternator, two-battery, 28-volt
direct current (VDC) electrical system designed to reduce the risk of
electrical system faults. The system provides uninterrupted power for
avionics, flight instrumentation, lighting, and other electrically operated
and controlled systems during normal operation.
Power Generation
Primary power for the SR22 is supplied by a 28-VDC, negative-ground
electrical system. The electrical power generation system consists of
two alternators controlled by a Master Control Unit (MCU) mounted on
the left side of the firewall and two batteries for starting and electrical
power storage.
Alternator 1 (ALT 1) is a gear-driven, internally rectified, 60-amp
alternator mounted on the right front of the engine. Alternator 2 (ALT 2)
is a gear-driven, internally rectified, 20-amp alternator mounted on the
accessory drive at the rear of the engine. ALT 1 is regulated to 28 volts
and ALT 2 is regulated to 28.75 volts. The output from ALT 1 is
connected to the Main Distribution Bus in the MCU through an 80-amp
fuse. The output from ALT 2 is connected to the Essential Distribution
Bus in the MCU through a 40-amp fuse. Both alternators are selfexciting
(not self-starting) and require battery voltage for field
excitation in order to start up - for this reason, the batteries should not
be turned off in flight.
Battery 1 (BAT 1) is an aviation grade 12-cell, lead-acid, 24-volt, 10-
amp-hour battery mounted on the right firewall. BAT 1 is charged from
the Main Distribution Bus in the MCU. Battery 2 (BAT 2) is composed
of two 12-volt, 7-amp-hour, sealed, lead-acid batteries connected in
series to provide 24 volts. Both BAT 2 units are located in a vented,
acid-resistant container mounted behind the aft cabin bulkhead (FS
222) below the parachute canister. BAT 2 is charged from the circuit
breaker panel Essential Bus.
The Master Control Unit (MCU) is located on the left firewall. The MCU
controls ALT 1, ALT 2, starter, landing light, external power, and power
generation functions. In addition to ALT 1 and ALT 2 voltage
regulation, the MCU also provides external power reverse polarity
protection, alternator overvoltage protection, as well as alternator fail
Revision A5
7-66 P/N 13772-001
Section 7 Cirrus Design
Airplane Description SR22
and overcurrent annunciations. Power is distributed to the airplane
circuit panel buses through Main and Essential buses in the MCU.
During normal operation, the alternators feed their respective
Distribution Bus independently (ALT 1 feeds Main Distribution Bus and
ALT 2 feeds the Essential Distribution Bus). The distribution busses
are interconnected by two 50-amp fuses and a diode. The diode
prevents ALT 2 from feeding the Main Distribution Bus. Additionally,
since ALT 2 / Essential Distribution Bus voltage is slightly higher than
ALT 1 / Main Distribution Bus voltage, ALT 1 will not feed the Essential
Distribution Bus unless ALT 2 fails.
Power Distribution
The power distribution system for the SR22 consists of the Main
Distribution Bus and the Essential Distribution Bus in the MCU and
associated buses in the Circuit Breaker panel. The circuit breaker
panel is located on the left side of the console next to the pilots right
knee.
For normal operation, the Essential Buses in the circuit breaker panel
are powered from the Essential Distribution Bus in the MCU through
25-amp circuit breakers. BAT 2 is connected directly to the Essential
Bus in the circuit breaker panel and will power the bus should the
voltage coming from the MCU distribution buses drop below the
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：CIRRUS DESIGN SR22西銳22飛行員操作手冊和飛機飛行手冊(77)