曝光臺 注意防騙 網曝天貓店富美金盛家居專營店坑蒙拐騙欺詐消費者

E. Flight Controls Hydraulic Module Installation
NOTE: Do not install Flight Control Module 65-44891-7 with serial number 8726 thru 8936. These
FCMs has compensators, 10-60560-3, with serial number 20478A thru 20717A installed.
These compensators are prohibited by AD 2002-19-51, Rev.1.
SUBTASK 27-09-21-020-003
(1) Remove protective caps from the open ports of the hydraulic module [1].
737-600/700/800/900
AIRCRAFT MAINTENANCE MANUAL
EFFECTIVITY
GUN ALL 27-09-21
Page 407
Oct 10/2007
D633A101-GUN
BOEING PROPRIETARY - Copyright#Unpublished Work - See title page for details
SUBTASK 27-09-21-420-003
(2) If they are not installed, install the unions [3], unions [5], reducer [11], packings [2], packings [4],
and packing [12] on the hydraulic module [1]:
(a) Apply MCS 352B fluid, D00054 (recommended) or fluid, D00153 (alternative) to the unions
[3], unions [5], reducer [11] and new packings [2], new packings [4], and new packing [12].
(b) Install the new packings [2] and unions [3] in ports 1, 2, 5 on the hydraulic module [1].
(c) Install the new packings [4] and unions [5] in ports 4 and 7 on the hydraulic module [1].
(d) Install the new packing [4] and check valve [10] in port 3 on the hydraulic module [1].
1) Install the check valve [10] with the free flow arrow pointed away from the hydraulic
module [1].
(e) Install the new packing [12] and reducer [11] in port 6 on the hydraulic module [1].
SUBTASK 27-09-21-020-004
(3) Remove the protective caps from the hydraulic tubing.
SUBTASK 27-09-21-420-004
(4) Install the hydraulic module [1]:
(a) Put the hydraulic module [1] on its mounting bracket.
(b) Connect the hydraulic module [1] to the top mounting bracket with the bolts [6] and washers
[7].
(c) Connect the hydraulic module [1] to the bottom mounting bracket with the bolts [8] and
washers [9].
(d) Connect the hydraulic tubing to the hydraulic module [1].
(e) Before you connect the electrical connectors [18], [13] and [14], examine the connectors for
corrosion.
WARNING: DO THE STEPS BELOW IF THE AIRPLANE OPERATES AT AIRPORTS WHERE
DEICING FLUID THAT CONTAIN POTASSIUM FORMATE IS USED. ALSO DO THE
STEPS FOR ALL AIRPLANES THAT YOU FOUND CORROSION IN THE
ELECTRICAL CONNECTORS IN THE MAIN WHEEL WELL. THE ELECTRICAL
CONNECTOR IS PART OF A SYSTEM THAT IS NECESSARY FOR SAFE FLIGHT.
(f) If there was corrosion, refer to (SWPM 20-60-03) to correct the problem.
(g) Apply the D5026NS or ZC-026 compound, G50171 to the connectors (SWPM 20-60-03).
(h) Connect the electrical connectors [18], [13] and [14] to the spoiler shutoff valve [16], the
flight controls shutoff valve [17], and the low pressure warning switch [15].
F. Put the Airplane Back to Its Usual Condition
SUBTASK 27-09-21-860-008
(1) Remove the safety tags and close these circuit breakers:
F/O Electrical System Panel, P6-2
Row Col Number Name
B 12 C00204 FLIGHT CONTROL SHUTOFF VALVES SPOILER
B 13 C00363 FLIGHT CONTROL SHUTOFF VALVES FLT CONT
C 13 C01074 FLIGHT CONTROL SHUTOFF VALVES FLT CONT
SUBTASK 27-09-21-610-001
(2) If it is necessary to service the hydraulic reservoirs, do this task: Hydraulic Reservoir
Servicing, TASK 12-12-00-610-801.
737-600/700/800/900
AIRCRAFT MAINTENANCE MANUAL
EFFECTIVITY
GUN ALL 27-09-21
Page 408
Oct 10/2007
D633A101-GUN
BOEING PROPRIETARY - Copyright#Unpublished Work - See title page for details
SUBTASK 27-09-21-730-001
(3) Do this task: Flight Controls Hydraulic Module Test, TASK 27-09-21-700-801.
------------------------- END OF TASK ---------------------------
737-600/700/800/900
AIRCRAFT MAINTENANCE MANUAL
EFFECTIVITY
GUN ALL 27-09-21
Page 409
Oct 10/2005
D633A101-GUN
BOEING PROPRIETARY - Copyright#Unpublished Work - See title page for details
FLIGHT CONTROLS HYDRAULIC MODULE - ADJUSTMENT/TEST
1. General
A. There is one task in this procedure which is the test of the flight controls hydraulic module.
B. The flight controls hydraulic module is referred to as the "hydraulic module" in this procedure.
C. The hydraulic module for hydraulic system A is found in the left main wheel well. The hydraulic
module for hydraulic system B is found in the right main wheel well.
TASK 27-09-21-700-801
2. Flight Controls Hydraulic Module Test
A. General
(1) In this procedure, the two hydraulic modules [1] are tested at the same time.
B. References
Reference Title
24-22-00-860-811 Supply Electrical Power (P/B 201)
29-11-00-860-801 Hydraulic System A or B Pressurization (P/B 201)
29-11-00-860-805 Hydraulic System A or B Power Removal (P/B 201)
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：737-600/700/800/900 AIRCRAFT MAINTENANCE MANUAL飛機維護手冊1(62)