曝光臺 注意防騙 網(wǎng)曝天貓店富美金盛家居專營店坑蒙拐騙欺詐消費者

27-11-34-200-801 Aileron Tab Control Rods Inspection (P/B 601)
B. Expendables/Parts
AMM Item Description AIPC Reference AIPC Effectivity
12 Pin 27-11-21-01-010 GUN 001-028, 101-121,
155-157, 201-999
17 Rod assembly 27-11-21-01-040 GUN 001-028, 101-121,
155-157, 201-999
C. Location Zones
Zone Area
211 Flight Compartment - Left
212 Flight Compartment - Right
572 Left Wing - Aileron
672 Right Wing - Aileron
D. Access Panels
Number Name/Location
571CB Lower Outboard Fixed Trailing Edge Access Panel
572DB Lower Aileron, Hinge Cover - WBL 469.00
572EB Lower Aileron, Hinge Cover - WBL 481.00
671CB Lower Outboard Fixed Trailing Edge Access Panel
672DB Lower Aileron, Hinge Cover - WBL 469.00
672EB Lower Aileron, Hinge Cover - WBL 481.00
E. Prepare for installation
SUBTASK 27-11-34-220-001
(1) If you install used bolts, bushings, bearings or other components with worn areas, do this task:
Aileron Tab Control Rods Inspection, TASK 27-11-34-200-801.
F. Aileron Tab Control Rods Installation
SUBTASK 27-11-34-420-001
(1) Install the control rod assembly [17]:
(a) Move the aileron trailing edge down.
(b) Put the two control rod assemblies [17] in position, align the rod ends with the attach
fittings.
NOTE: The length of the control rod assembly [17] must be the same as those written
down after the removal.
(c) Connect the control rod assembly [17] to the tab mast with the bolts [19], washers [8],
bushings [18], washers [10], and nuts [11].
737-600/700/800/900
AIRCRAFT MAINTENANCE MANUAL
EFFECTIVITY
GUN ALL 27-11-34
Page 405
Jun 10/2007
D633A101-GUN
BOEING PROPRIETARY - Copyright#Unpublished Work - See title page for details
1) Adjust the length of the control rod assembly [17] if it is necessary.
2) Tighten the nuts [11] to 50-80 pound-inches (5.6-9.0 newton-meters).
3) Install the new pins [12].
(d) Lift up the aileron trailing edge.
(e) Install the bolts [7], washers [8], bushings [9], washers [10] and nuts [11] to connect the
control rod assembly [17] to the forward fittings.
1) Tighten the nut [11] to 50-80 pound-inches (5.6-9.0 newton-meters) until the next nut
castellation aligns with the hole in the bolt.
2) Install the pins [12].
(f) Install the radial seal [16] and radial seal retainer [15] to the structure with the bolts [13] and
washers [14].
SUBTASK 27-11-34-410-001
(2) Install these access panels:
(a) On the left wing, close these access panels:
Number Name/Location
571CB Lower Outboard Fixed Trailing Edge Access Panel
572DB Lower Aileron, Hinge Cover - WBL 469.00
572EB Lower Aileron, Hinge Cover - WBL 481.00
(b) On the right wing, close these access panels:
Number Name/Location
671CB Lower Outboard Fixed Trailing Edge Access Panel
672DB Lower Aileron, Hinge Cover - WBL 469.00
672EB Lower Aileron, Hinge Cover - WBL 481.00
SUBTASK 27-11-34-420-002
(3) Install the bolts [4] to attach the aft removable fairing [3] to the aileron balance tab [5].
SUBTASK 27-11-34-420-003
(4) Install the bolts [6] to attach the forward removable fairing [2] to the aileron [1].
SUBTASK 27-11-34-710-001
(5) Move the aileron control wheel through full travel.
(a) Make sure that the aileron tab moves freely.
SUBTASK 27-11-34-220-002
(6) Make sure the distance from the tab trailing edge to the extension of the aileron bottom surface
is correct. To measure it, do this task: Aileron Balance Tab Adjustment,
TASK 27-11-00-820-803.
SUBTASK 27-11-34-820-001
(7) Do this task: Flight Test to Find and Correct Asymmetrical Flight Control Forces ,
TASK 27-11-00-750-801.
------------------------- END OF TASK ---------------------------
737-600/700/800/900
AIRCRAFT MAINTENANCE MANUAL
EFFECTIVITY
GUN ALL 27-11-34
Page 406
Jun 10/2007
D633A101-GUN
BOEING PROPRIETARY - Copyright#Unpublished Work - See title page for details
AILERON TAB CONTROL RODS - INSPECTION/CHECK
1. General
A. This procedure contains the task to do an inspection of the aileron tab control rods.
TASK 27-11-34-200-801
2. Aileron Tab Control Rods Inspection
(Figure 601)
A. General
(1) This task gives wear limits and repair data for the aileron tab control rods inspection.
B. References
Reference Title
27-11-21-000-801 Aileron Balance Tab Removal (P/B 401)
27-11-21-400-801 Aileron Balance Tab Installation (P/B 401)
27-11-34-000-801 Aileron Tab Control Rods Removal (P/B 401)
27-11-34-400-801 Aileron Tab Control Rods Installation (P/B 401)
C. Tools/Equipment
Reference Description
STD-1096 Micrometer - Depth, 0-1 Inch, Readable to 1/1000 Inch
　
中國航空網(wǎng) m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：737-600/700/800/900 AIRCRAFT MAINTENANCE MANUAL飛機(jī)維護(hù)手冊1(156)