曝光臺 注意防騙 網曝天貓店富美金盛家居專營店坑蒙拐騙欺詐消費者

311 Area Aft of Pressure Bulkhead - Left
312 Area Aft of Pressure Bulkhead - Right
C. Location of the FLight Control Cables Air Pressure Seals
SUBTASK 27-09-17-860-001
(1) Find the air pressure seals (Table 201).
Table 201/27-09-17-993-802
Cable System Number of Seals Location Access Panel Number
Left Elevator Cables 2 Aft Pressure Bulkhead 311BL
Right Elevator Cables 2 Aft Pressure Bulkhead 311BL
Rudder Cables 2 Aft Pressure Bulkhead 311BL
Stabilizer Trim Cables 2 Aft Pressure Bulkhead 311BL
Speed Brake Cables 2 Left Wheel Well Ceiling Wheel Well
SUBTASK 27-09-17-960-001
(2) If it is necessary to remove the seals, do this task: Control Cable Air Seal Removal,
TASK 20-10-04-000-801.
SUBTASK 27-09-17-960-002
(3) If it is necessary to install the seals, do this task: Control Cable Air Seal Installation,
TASK 20-10-04-400-801.
------------------------- END OF TASK ---------------------------
737-600/700/800/900
AIRCRAFT MAINTENANCE MANUAL
EFFECTIVITY
GUN ALL 27-09-17
Page 201
Feb 10/2004
D633A101-GUN
BOEING PROPRIETARY - Copyright#Unpublished Work - See title page for details
Flight Control Cable Air Pressure Seals
Figure 201 (Sheet 1 of 2)/27-09-17-990-801
737-600/700/800/900
AIRCRAFT MAINTENANCE MANUAL
EFFECTIVITY
GUN ALL 27-09-17
Page 202
Oct 10/2003
D633A101-GUN
BOEING PROPRIETARY - Copyright#Unpublished Work - See title page for details
Flight Control Cable Air Pressure Seals
Figure 201 (Sheet 2 of 2)/27-09-17-990-801
737-600/700/800/900
AIRCRAFT MAINTENANCE MANUAL
EFFECTIVITY
GUN ALL 27-09-17
Page 203
Oct 10/2003
D633A101-GUN
BOEING PROPRIETARY - Copyright#Unpublished Work - See title page for details
FLIGHT CONTROLS HYDRAULIC MODULE - REMOVAL/INSTALLATION
1. General
A. This procedure has these tasks:
NOTE: Do not install Flight Control Module 65-44891-7 with serial number 8726-8936 unless the
compensators, 10-60560-3, with serial number 20478A thru 20717A is not installed.
Compensators, 10-6050-3, with serial number 20478A thru 20717A are prohibited by AD
2002-19-51, Rev.1.
(1) A removal of the flight controls hydraulic module
(2) An installation of the flight controls hydraulic module.
B. The flight controls hydraulic module is referred to as the "hydraulic module" in this procedure.
C. There are two hydraulic modules installed on the airplane. The hydraulic module for the hydraulic
system A is found in the left main wheel well. The hydraulic module for the hydraulic system B is
found in the right main wheel well.
D. Each hydraulic module contains these components:
(1) A check valve
(2) A low pressure warning switch
(3) A compensator cartridge
(4) A spoiler shutoff valve
(5) A flight controls shutoff valve.
TASK 27-09-21-000-801
2. Flight Controls Hydraulic Module Removal
(Figure 401)
A. References
Reference Title
29-09-00-860-802 Hydraulic Reservoirs Depressurization (P/B 201)
29-11-00-860-805 Hydraulic System A or B Power Removal (P/B 201)
29-11-01-860-802 Hydraulic Reservoirs Depressurization (P/B 201)
32-00-01-480-801 Landing Gear Downlock Pins Installation (P/B 201)
B. Tools/Equipment
Reference Description
STD-1110 Container - Hydraulic Fluid Resistant, 5 Gallon (19 Liters)
C. Location Zones
Zone Area
133 Main Landing Gear Wheel Well, Body Station 663.75 to Body Station
727.00 - Left
134 Main Landing Gear Wheel Well, Body Station 663.75 to Body Station
727.00 - Right
211 Flight Compartment - Left
212 Flight Compartment - Right
737-600/700/800/900
AIRCRAFT MAINTENANCE MANUAL
EFFECTIVITY
GUN ALL 27-09-21
Page 401
Jun 10/2004
D633A101-GUN
BOEING PROPRIETARY - Copyright#Unpublished Work - See title page for details
D. Prepare for the Removal
SUBTASK 27-09-21-480-001
WARNING: MAKE SURE THE DOWNLOCK PINS ARE INSTALLED ON ALL THE LANDING GEARS.
WITHOUT THE DOWNLOCK PINS, THE LANDING GEARS COULD RETRACT AND
CAUSE INJURIES TO PERSONS AND DAMAGE TO EQUIPMENT.
(1) If the downlock pins are not installed on all the landing gears, do this task: Landing Gear
Downlock Pins Installation, TASK 32-00-01-480-801.
SUBTASK 27-09-21-860-005
(2) If there is power on hydraulic systems A and B, remove hydraulic power. To remove power from
hydraulic systems A and B, do this task: Hydraulic System A or B Power Removal,
TASK 29-11-00-860-805.
SUBTASK 27-09-21-860-006
(3) Do this task: Hydraulic Reservoirs Depressurization, TASK 29-11-01-860-802 or Hydraulic
Reservoirs Depressurization, TASK 29-09-00-860-802.
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：737-600/700/800/900 AIRCRAFT MAINTENANCE MANUAL飛機維護手冊1(60)