曝光臺(tái) 注意防騙 網(wǎng)曝天貓店富美金盛家居專營店坑蒙拐騙欺詐消費(fèi)者

supported
Check programming m
parameters
-226 " ore transient lists
programmed have
e length or
transient cannot be compiled and
"Lists not same length One or m
different length.
All lists must be of sam
executed.
-241 "Hardware missing" N/A N/A
-254 "Media full" No storage space left to ke
save settings or data.
Delete other settings or data to ma
room.
-255 “Directory full” Too many waveform
directory entries
Delete one or more waveforms from
waveform memory to make room.
-256 t for waveform
names present.
“File name not found” Waveform requested no
in directory
Check waveform directory
-257 “File name error” Incorrect filename Too many or non-ASCII characters used
in waveform file definition.
-283 “Illegal variable name” Variable name illegal. Use ASCII characters only
-300 "Device specific error" Hardware related error Check hardware for proper operation.
-311 ernload.
Check
lear
Alternatively, use TRAC:DEL:ALL
command to clear waveform memory.
"Memory error" Waveform memory
checksum error.
May be the result of incomplete us
defined waveform dow
interface and try downloading waveform
again. Successful download may c
this error condition.
California Instruments 147
User Manual Compact i/iX Series
Number Message String Cause Remedy
-314 "Save/recall memory .
lost"
User setup register
contents lost
Store setup in same register again
-315 "Configuration memory
lost"
Contact CI service department at
support@calinst.com
Hardware configuration
settings lost. to obtain
data.
instructions on restoring configuration
-330 "Self-test failed" Internal error
support@calinst.com
Contact CI service department at
-350 "Queue overflow" Message queue full. Too many messages. Read status using
SYST:ERR query until 0, "No Error" is
received indicating queue empty.
-400 r" ry. Check programming manual for correct
query format and parameters
"Query erro Unable to complete que
-410 ED"
t read.
correct
flow. Response must be read after each
"Query INTERRUPT Query issued but
response no
Check application program for
query to avoid this error.
-420
INATED"
Query incomplete. or after query
command.
"Query
UNTERM
Check for terminat
-430 "Query DEADLOCKED" Query cannot be
completed
Check application program for multiple
queries
-440 "Query Check for terminator after query
UNTERMINATED"
Query incomplete.
command.
0 "No error" No errors in queue
2 " Non-volatile RAM ice department at
CONFIG section
checksum failed"
Controller failure during
Self-test.
Contact CI serv
support@calinst.com
3 " Non-volatile RAM CAL
section checksum failed"
Controller failure during
Self-test.
Contact CI service department at
support@calinst.com
4 " Non-volatile RAM
WAVEFORM section
checksum failed"
Controller failure during
Self-test.
Contact CI service department at
support@calinst.com
10 "Ram self test Controller failure during Contact CI service department at
Self-test. support@calinst.com
40 "Voltage self test error, plifier in Master e department at
output 1
No. 1/A am
source has no output
during Self-test.
Contact CI servic
support@calinst.com
41 st error, B amplifier in Master
.
Contact CI service department at
upport@calinst.com
"Voltage self te
output 2
No. 2/
source has no output
during Self-test. Three
phase models only
s
42 "Voltage self test error,
output 3 source has no
.
No. 3/C amplifier in
Master
output during Self-test
Three phase models only
Contact CI service department at
support@calinst.com
43 ,
during Self-test.
vice department at
support@calinst.com
"Current self test error
output 1
No. 1/A amplifier in Aux.
Source has no output
Contact CI ser
44 "Current self test error,
output 2
No. 2/B amplifier in Aux.
Source has no output
during Self-test. Three
phase models only.
Contact CI service department at
support@calinst.com
　
中國航空網(wǎng) m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：航空資料11(162)