曝光臺 注意防騙 網(wǎng)曝天貓店富美金盛家居專營店坑蒙拐騙欺詐消費者

shown in Figure 10-4.
y Menu
:
The above tests can be selected by scrolling to the highlighted selection using the up and down key
and the ENTER key to start the selected test.
Figure 10-4: Emergenc
The EMERGENCY SCREEN has the following tests
1 VOLTAGE
2 FREQUENCY
Note: These tests are only required for revision D. See steady state voltage and frequency
tests for all other revisions.
VOLTAGE
This test will change the output voltage in the following sequence:
• 104V for 1 minute.
The
FREQU
This test will change the output frequency in the following sequence:
• 440Hz for 1 minute.
• 122V for 1 minute.
• 115V for 1 minute.
← key (backspace) will terminate the test at any time.
ENCY
• 360Hz for 1 minute.
• 400Hz for 1 minute.
The ← key (backspace) will terminate the test at any time.
California Instruments 135
User Manual Compact i/iX Series
10.6.3 Abnormal Test
From the MIL704 main menu Figure 10-2) scroll to the ABNORMAL AC entry using the up and down
cursor keys. Press the ENTER key to select the ABNORMAL screens. The screen will appear as
shown in Figure 10-5.
NOR EEN has :
. OVE A
. UND LT
3. OVER FREQUENCY
the highlighted selection using the up and down key
OVER V
output voltage for the selected phase in the following sequence:
• 180V for 50msec.
The voltage gradually decays with time to 125 volt b he following
V = 2. or ≤ 6.925
Stay at 125V for 93 seconds before returning to 115V.
For 60Hz only:
• 180V for 3.34msec
1.947
• Stay at 122V for 8 seconds before returning to 115V.
Note: Prior to the test, a voltage range change may take place if the power source is set for the low
voltage range. This will cause the EUT to loose power momentarily. If this is not acceptable, the power
source must be left in high range at all times.
The ← key (backspace) will terminate the test at any time.
UNDER VOLTAGE
This test will change the output voltage for the selected phase in the following sequence:
For 400Hz and VFREQ:
• 0V for 7 seconds.
• 100V for 93 seconds.
For 60Hz only
Figure 10-5: Abnormal Screens
The AB MAL SCR the following tests
1 R VOLT GE
2 ER VO AGE
4. UNDER FREQUENCY
The above test can be selected by scrolling to
and the ENTER key to start the selected test.
OLTAGE
This test will change the
For 400Hz and VFREQ:
• y t equation:
124.6 + 77/t. F 0.05 ≤ t
•
• The Voltage gradually decays with time to 122 volt by the following equation:
V = 121.7 + 0.583/t. For 0.00334 ≤ t ≤
California Instruments 136
User Manual Compact i/iX Series
• 0V for 2 se
• 100V for 8 seconds.
conds.
This test will change the output frequency in the sequence shown in Table 10-4 before returning to the
The ← key (backspace) will terminate the test at any time.
OVER FREQUENCY
steady state frequency.
The ← key (backspace) will terminate the test at any time.
Revision D E F F 60Hz only
FREQ Time FREQ Time FREQ TIME FREQ TIME
Seq1 480Hz 5sec. 480Hz 5sec. 480Hz 5sec 61Hz 7sec
Seq2 420Hz 5sec 420Hz 9sec 420Hz 5sec 60.5Hz 8sec
Table 10-4: Abnormal Over Frequency
serted at the nominal test frequency. The ← key
UNDER FREQUENCY
equence shown in Table 10-5 before returning to
a .
e ) will terminate the test at any time.
After this sequence, a 5 second delay will be in
(backspace) will terminate the test at any time.
This test will change the output frequency in the s
ste dy state frequency
Th ← key (backspace
Revision D E F F 60Hz only
FREQ Time FREQ Time FREQ TIME FREQ TIME
Seq1 0 5sec. 0Hz 7sec. 0Hz 7sec 0Hz 7sec
Seq2 375Hz 5sec 380Hz 7sec 380Hz 3sec 59.5Hz 8sec
Table 10-5: Abnormal Under Frequency
After this sequence, a 5 second delay will be inserted at the nominal test frequency. The ← key
(backspace) will terminate the test at any time.
California Instruments 137
User Manual Compact i/iX Series
10.7 DC Test Mode
DC test mode requires DC mode and a steady state voltage setting of 28V DC or 270V DC.
10.7.1 Steady State Test
Scroll to the STEADY STATE entry using the up and down cursor keys. Press the ENTER key to
select the STEADY STATE screen.
4 STEADY STATE screen has the following tests:
e selected by scrolling to the highlighted selection using the up and down key
d d test.
VOLTAGE
This test will change the output voltage for the selected phase in the following sequence:
　
中國航空網(wǎng) m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：航空資料11(158)