曝光臺 注意防騙 網(wǎng)曝天貓店富美金盛家居專營店坑蒙拐騙欺詐消費(fèi)者

USB cable between the AC Source and a PC or USB Hub may be used.
Note: Use of the USB port to control more than one power source from a single PC is not
recommended, as communication may not be reliable. Use GPIB interface for multiple
power source control.
Fig 4: USB C pin orientation.
ure 3- onnector
Pin Name Description
1 VBUS +5 VDC
2 D- Data -
3 D+ Data +
4 GND Ground
Table 3-7: USB Connector pin out.
3.7.7 GPIB Interface – J33
A standard IEEE488/ANSI MC1.1; 24 pin GPIB connector is located on the rear panel on al iX models.
Maximum cable length is 20 meters, or 2 meters per device - whichever is less. Maximum number of
devices is 15. Devices may be connected in either a Star or Linear fashion. Set crews with Metric
s
Note: mo ce is option f n alle ot
thread are black.
On “i” dels, the GPIB interfa al. I ot inst d, this connector is n
present.
Pin # Signal
Names
Signal Description Pin # Signal
Names
Signal Description
1 DIO1 Data Input/Output Bit 1 13 DIO5 Data Input/Output Bit 5
2 DIO2 Data Input/Output Bit 2 14 DIO6 Data Input/Output Bit 6
3 DIO3 Data Input/Output Bit 3 15 DIO7 Data Input/Output Bit 7
4 DIO4 Data Input/Output Bit 4 16 DIO8 Data Input/Output Bit 8
5 EOI End-Or-Identify 17 REN Remote Enable
6 DAV Data Valid 18 Shield Ground (DAV)
7 NRFD Not Ready For Data 19 Shield Ground (NRFD)
8 NDAC Not Data Accepted 20 Shield Ground (NDAC)
9 IFC Interface Clear 21 Shield Ground (IFC)
10 SRQ Service Request 22 Shield Ground (SRQ)
11 ATN Attention 23 Shield Ground (ATN)
California Instruments 39
User Manual Compact i/iX Series
Pin # Signal
Names
Signal Description Pin # Signal
Names
Signal Description
12 Shield Chassis Ground 24 Single
GND
Signal Ground.
Table 3-8: GPIB Interface Connector pin out.
3.7.8 LAN Interface – RJ45 – J35
An optional RJ45 Ethernet 10BaseT connector is located on the rear panel for remote control. A
dministrator for directions on connecting the AC source to any corporate LAN.
If the –LAN Ethernet interface option is present, the MAC Address (Media Access Control) of the
Ethernet port is printed on the serial tag of the power source. The serial tag is located on the rear
panel of the unit.
For information on how to set up a network connection or a direct PC connection using the LAN
interface, refer to the i/iX Series Programming Manual P/N 6005-961 distributed in Adobe PDF format
on CD ROM CIC496.
standard RJ45 UTP patch cord between the AC Source and a network Hub may be used to connect
the AC source to a LAN. For direct connection to a PC LAN card, a crossover RJ45 cable is required.
Consult your network a
LAN
Pin Ethernet TPE
10BaseT/100BastT/1000BaseT
EIA/TIA 568A EIA/TIA 568B
Crossover
1 Transmit/Receive Data 0 + White with green stripe White with orange stripe
2 Transmit/Receive Data 0 - Green with white stripe or
solid green
Orange with white stripe or
solid orange
3 Transmit/Receive Data 1 + White with orange stripe White with green stripe
4 Transmit/Receive Data 2 + ite stripe or
solid blue
Blue with white stripe or Blue with wh
solid blue
5 Transmit/Receive Data 2 - White with blue stripe White with blue stripe
6 Transmit/Receive Data 1 - Orange with white stripe
or solid orange
Green with white stripe or
solid
7 Transmit/Receive Data 3 + White with brown stripe or
solid brown
White with brown stripe or
solid brown
8 Transmit/Receive Data 3 - Brown with white stripe or
solid brown.
Brown with white stripe or
solid brown
Table 3-9: RJ45 LAN Connector pin out.
California Instruments 40
User Manual Compact i/iX Series
3.8 Basic Initial Functional Test
CAUTION: Work carefully when performing these tests; hazardous voltages are
present on the input and output during this test.
Refer to Figure 3-5 for the required functional test set up. Proceed as follows to perform a basic
1. witch at the
2.
ll load test and that the load used does not exceed the maximum power
4. e power source using the On/Off switch on the front panel. Allow the power source to
5.
ut although the DMM may show a noise level, especially if the
6. ge (20 VAC). Observe the
8. oltage range or 230V on
9. screen by pressing the Meas button. The output voltage, current and
Section 6 or call California Instrument’s customer satisfaction department for further
assistance.
function check of the power system:
Verify the correct AC line input rating on the nameplate and the AC line input selector s
　
中國航空網(wǎng) m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：航空資料11(125)