曝光臺 注意防騙 網(wǎng)曝天貓店富美金盛家居專營店坑蒙拐騙欺詐消費者

codes changed significantly in 2005 and are shown in
Figure 3-47.
Figure 3-45. U.S. Standard RNP Levels.
3-41
FL 330
FL 310
FL 290
FL 280
FL 270
2000 ft
1000 ft
Figure 3-46. Prior to implementation of RVSM, all traffic above FL290 required vertical separation of 2,000 feet.
Figure 3-47. When filed in your IFR flight plan, these codes inform ATC about your aircraft navigation capability.
No DME DME TACAN only Area Navigation (RNAV)
LORAN, VOR/DME, or INS
/D
/B
/A
/M
/N
/P
/Y
/C
/ I
/X
/T
/U
/E
/F
/G
/R
RVSM
/J
/K
/L
/Q
/W
No transponder
Transponder without Mode C
Transponder with Mode C
Advanced RNAV with transponder and Mode C
(If an aircraft is unable to operate with a transponder
and/or Mode C, it will revert to the appropriate code
listed above under Area Navigation.)
With RVSM
3-42
4-1
Preparation for the arrival and approach begins long
before the descent from the en route phase of flight.
Planning early, while there are fewer demands on your
attention, leaves you free to concentrate on precise
control of the aircraft and better equipped to deal with
problems that might arise during the last segment of
the flight.
TRANSITION FROM EN ROUTE
This chapter focuses on the current procedures
pilots and air traffic control (ATC) use for instrument flight rule (IFR) arrivals in the National
Airspace System (NAS). The objective is to provide
pilots with an understanding of ATC arrival procedures and pilot responsibilities as they relate to the
transition between the en route and approach phases
of flight. This chapter emphasizes standard terminal
arrival routes (STARs), descent clearances, descent
planning, and ATC procedures, while the scope of
coverage focuses on transitioning from the en route
phase of flight, typically the origination point of a
STAR to the STAR termination fix. This chapter
also differentiates between area navigation (RNAV)
STARs and STARs based on conventional navigational aids (NAVAIDs).
Optimum IFR arrival options include flying directly
from the en route structure to an approach gate or initial
approach fix (IAF), a visual arrival, STARs, and radar
vectors. Within controlled airspace, ATC routinely uses
radar vectors for separation purposes, noise abatement
considerations, when it is an operational advantage, or
when requested by pilots. Vectors outside of controlled airspace are provided only on pilot request. The
controller tells you the purpose of the vector when the
vector is controller-initiated and takes the aircraft off a
previously assigned nonradar route. Typically, when
operating on RNAV routes, you are allowed to remain
on your own navigation.
TOP OF DESCENT
Planning the descent from cruise is important because of
the need to dissipate altitude and airspeed in order to
arrive at the approach gate properly configured.
Descending early results in more flight at low altitudes
with increased fuel consumption, and starting down late
results in problems controlling both airspeed and
descent rates on the approach. Top of descent (TOD)
from the en route phase of flight for high performance
airplanes is often used in this process and is calculated
manually or automatically through a flight management
system (FMS) [Figure 4-1], based upon the altitude of
Figure 4-1. Top of Descent and FMS Display.
PROGRESS 2 / 3
SPD / ALT CMD VS@TOD
240 / 3000 2400
TOC FUEL QTY
151 . 5NM / 00 + 23 20000
TOD GROSS WT
1022NM / 02 + 17 62850
AIR DATA FLT SUM
Top of
Descent
4-2
the approach gate. The approach gate is an imaginary
point used by ATC to vector aircraft to the final approach
course. The approach gate is established along the final
approach course 1 nautical mile (NM) from the final
approach fix (FAF) on the side away from the airport
and is located no closer than 5 NM from the landing
threshold. The altitude of the approach gate or initial
approach fix is subtracted from the cruise altitude, and
then the target rate of descent and groundspeed is
applied, resulting in a time and distance for TOD, as
depicted in Figure 4-1 on page 4-1.
Achieving an optimum stabilized, constant rate descent
during the arrival phase requires different procedures
for turbine-powered and reciprocating-engine airplanes. Controlling the airspeed and rate of descent is
important for a stabilized arrival and approach, and it
　
中國航空網(wǎng) m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：Instrument Procedures Handbook (IPH)儀表程序手冊上(87)