曝光臺 注意防騙 網曝天貓店富美金盛家居專營店坑蒙拐騙欺詐消費者

For example, at 10 NM the aircraft should be 3,000
feet above the TDZE, at 5 NM 1,500 feet, at 2 NM
600 feet, at 1.5 NM 450 feet, etc., until a safe landing
can be made. In the above example the aircraft should
arrive at the MDA (800 feet MSL) approximately 1.3
NM from the threshold and in a position to land in the
touchdown zone. Techniques for deriving a “300-to1” glidepath include using distance measuring equipment (DME), distance advisories provided by
radar-equipped control towers, RNAV (exclusive of
Omega navigation systems), GPS, dead reckoning,
and pilotage when familiar features on the approach
course are visible. The runway threshold should be
crossed at a nominal height of 50 feet above the
TDZE.
TRANSITION TO VISUAL
The transition from instrument flight to visual
flight during an instrument approach can be very
challenging, especially during low visibility operations. Additionally, single-pilot operations make
the transition even more challenging. Approaches
with vertical guidance add to the safety of the
transition to visual because the approach is
already stabilized upon visually acquiring the
required references for the runway. One hundred
to 200 feet prior to reaching the DA, DH, or MDA,
most of the PM’s attention should be outside of
the aircraft in order to visually acquire at least one
visual reference for the runway, as required by the
regulations. The PF should stay focused on the
instruments until the PM calls out any visual aids
that can be seen, or states “runway in sight.” The
PF should then begin the transition to visual
flight. It is common practice for the PM to call out
the V/S during the transition to confirm to the PF
that the instruments are being monitored, thus
allowing more of the PF’s attention to be focused
on the visual portion of the approach and landing.
Any deviations from the stabilized approach criteria should also be announced by the PM.
Single-pilot operations can be much more challenging because the pilot must continue to fly by the
instruments while attempting to acquire a visual
reference for the runway. While it is important for
both pilots of a two-pilot aircraft to divide their
attention between the instruments and visual references, it is even more critical for the single-pilot
operation. The flight visibility must also be at least
the visibility minimum stated on the instrument
approach chart, or as required by regulations. CAT
II and III approaches have specific requirements
that may differ from CAT I precision or nonprecision approach requirements regarding transition to
visual and landing. This information can be found
in the operator’s OpsSpecs or Flight Operations
Manual.
The visibility published on an approach chart is
dependent on many variables, including the height
above touchdown for straight-in approaches, or height
above airport elevation for circling approaches. Other
factors include the approach light system coverage, and
type of approach procedure, such as precision, nonprecision, circling or straight-in. Another factor determining the minimum visibility is the penetration of the
34:1 and 20:1 surfaces. These surfaces are inclined
planes that begin 200 feet out from the runway and
5-32
extend outward to 10,000 feet. If there is a penetration
of the 34:1 surface, the published visibility can be no
lower than 3/4 SM. If there is penetration of the 20:1
surface, the published visibility can be no lower than 1
SM with a note prohibiting approaches to the affected
runway at night (both straight-in and circling). [Figure
5-21] Circling may be permitted at night if penetrating
obstacles are marked and lighted. If the penetrating
obstacles are not marked and lighted, a note is published that night circling is “Not Authorized.” Pilots
should be aware of these penetrating obstacles when
entering the visual and/or circling segments of an
approach and take adequate precautions to avoid them.
For RNAV approaches only, the presence of a grey
shaded line from the MDA to the runway symbol in the
profile view, is an indication that the visual segment
below the MDA is clear of obstructions on the 34:1
slope. Absence of the gray shaded area indicates the
34:1 OCS is not free of obstructions.
MISSED APPROACH
Many reasons exist for executing a missed approach.
The primary reason, of course, is that the required
flight visibility prescribed in the IAP being used does
not exist or the required visual references for the runway cannot be seen upon arrival at the DA, DH or
MAP. In addition, according to Part 91, the aircraft
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：Instrument Procedures Handbook (IPH)儀表程序手冊上(124)