MAXIMUM PERMITTED SIDEPLAY
REPLACE THE WORN BUSHINGS
THE PART IS REPAIRABLE; REFER TO THE COMPONENT MAINTENANCE MANUAL FOR THE REPAIR INSTRUCTIONS.
Nose Landing Gear Tow Fitting Wear Limits
Figure 601 (Sheet 2)
32-21-13
ALL ú ú 01 Page 603 ú Jun 20/90
A
757 MAINTENANCE MANUAL
NOSE GEAR LOCK SPRING - REMOVAL/INSTALLATION
____________________________________________
TASK 32-21-15-004-001
1. Remove the Gear Lock Spring for the Nose Landing Gear (Fig. 401)
_____________________________________________________
A. Equipment
(1)
Downlock Spring Extender, MLG AND NLG -B32002-1
B.
References
(1)
29-11-00/201, Pressurize/Depressurize Main Hydraulic System
(2)
32-00-15/201, Landing Gear Door Locks
(3)
32-00-20/201, Landing Gear Downlocks
C.
Access
(1)
Location Zones
711 Nose Landing Gear (NLG)
713/714 Forward NLG Doors
715/716 Aft NLG Doors
730/740 Main Landing Gear and Doors
D.
Prepare for the Removal of the Lock Spring
S 494-002
(1) Make sure the downlocks are installed on the nose and main landing gear (Ref 32-00-20).
S 494-018
ú WARNING: THE DOORS
_______OBEY THE INSTALLATION PROCEDURE FOR THE DOOR LOCKS. ú OPEN AND CLOSE QUICKLY. THE MOVEMENT OF THE DOORS CAN CAUSE ú INJURIES TO PERSONS AND DAMAGE TO EQUIPMENT. ú
(2)
Open the doors for the landing gear and install the door locks (Ref 32-00-15).
(3)
Remove the pressure from the left hydraulic system (Ref 29-11-00).
S 864-004
32-21-15
ALL ú ú 01.1 Page 401 ú Sep 28/02
A
757
MAINTENANCE MANUAL
SEEA
SPRING
SPACER SPRING TERMINAL
END CAP
BOLT WASHER NUT (2 LOCATIONS)
LOCK SPRING B
FORWARD
B
LOCK LINK
A
WALL FITTINGS OF THE AFT WHEEL WELL SPRING SPACER END CAP SPRING TERMINAL
AFT LOCK LINK A-A SPRING SUPPORT SHAFT
A AFT LOCK LINK
LOCK SPRING A
Lock Spring Installation for the Nose Landing Gear
Figure 401 (Sheet 1)
32-21-15
ALL ú ú 01 Page 402 ú Mar 20/90
A
757 MAINTENANCE MANUAL
E. Remove the Lock Spring
S 014-005
(1)
Remove the bolt from the spring spacer at the aft end of the spring. Remove the end cap (View A-A).
S 014-006
(2)
Remove the nut and the tang washer from the forward end of the spring (View B-B).
SPRING SUPPORT SHAFT TANG WASHER
SPRING
FORWARD
SPACER
LOCK LINK
TANG WASHER SPRING SUPPORT SHAFT
Lock Spring Installation for the Nose Landing Gear Figure 401 (Sheet 2)
32-21-15
ALL ú ú 01 Page 403 ú Dec 20/90
A
757
MAINTENANCE MANUAL
S 494-007
(3)
Install the spring extender on the spring. Use the instructions supplied with the tool.
S 024-008
(4)
Remove the spring from the support shaft of the lock spring.
TASK 32-21-15-404-009
2. Install the Lock Spring for the Nose Landing Gear (Fig. 401)
_________________________________________________
A. Equipment
(1)
Downlock Spring Extender, MLG AND NLG -B32002-1
B.
Consumable Materials
(1)
D00633 Grease - BMS 3-33 (Recommended)
(2)
D00013 Grease - MIL-G-23827 (Alternative)
C.
References
(1)
32-00-15/201, Landing Gear Door Locks
D.
Access
(1)
Location Zones
711 Nose Landing Gear (NLG)
713/714 Forward NLG Doors
715/716 Aft NLG Doors
730/740 Main Landing Gear and Doors
E.
Install the Lock Spring
S 644-010
(1)
Apply grease to the bolts, the washers, the spacers, and the shaft before you install them.
S 494-012
(2)
Install the spring extender on the spring. Use the instructions supplied with the tool.
S 844-013
(3) 中國航空網 m.k6050.com 航空翻譯 www.aviation.cn 本文鏈接地址：757 AMM 飛機維護手冊 起落架 CHAPTER 32 - LANDING GEAR 2(9)
