(3)  
AMM 32-00-20/201, Landing Gear Downlocks

 (4)  
AMM 32-09-02/201, Prepare the Safety-Sensitive Systems for Air Mode Simulation

 B.  
Equipment

 (1)  
Pin Insertion/Extraction Tool
 Part on Crimp Tool Kit - DMC 567
 Daniels Manufacturing Corp.
 526 Thorpe Road
 Orlando, Forida 32824

 C.  
Access

 (1)  
Location Zones
 731 Main Landing Gear, LH
 741 Main Landing Gear, RH

 D.  
Prepare for Removal

 S 494-002
 (1)  Make sure the downlocks for the nose and main landing gear are installed (AMM 32-00-20/201).
 S 864-029
 WARNING: MAKE SURE YOU DO THE STEPS TO PREPARE THE SYSTEMS FOR AIR MODE
_______ CORRECTLY. IF YOU DO NOT FOLLOW THESE INSTRUCTIONS, INJURIES TO PERSONS OR DAMAGE TO EQUIPMENT CAN OCCUR.
 (2)  
Do the task to prepare the safety-sensitive systems for air mode simulation (AMM 32-09-02/201).

 S 864-003

 (3)  
Remove the pressure from the left hydraulic system and the hydraulic reservoir (AMM 29-11-00/201).

 32-32-15
 ALL  ú ú 01 Page 401 ú Sep 28/00
 
A

757
MAINTENANCE MANUAL

SHOCK DRAG STRUT STRUT TRUCK POSITIONER ACTUATOR
SEE A
B A
B  2. WASHER  3. TRUCK POSITIONER 
A  (2 LOCATIONS)  ACTUATOR 
4. ANTIROTATION 
BOLT 
FWD  TRUCK  1. PIN  1 
BEAM  5. COLLAR 

6.
 WASHER

7.
 NUT

9. WASHER (2 LOCATIONS)
3. TRUCK POSITIONER
TRUCKACTUATOR BEAM
8. PIN 2  10. ANTIROTATION
BOLT  A-A
11.
 COLLAR

12.
 WASHER

13.
 NUT

SHOCK 1 INSTALL THE PIN HEAD OUTBOARD STRUT FOR THE LEFT MAIN LANDING GEAR AND INBOARD FOR THE RIGHT LANDING GEAR
B-B
2 INSTALL THE PIN HEAD INBOARD
Main Landing Gear Truck Positioner Actuator Installation
Figure 401 (Sheet 1)

 32-32-15
 ALL  ú ú 02 Page 402 ú Dec 20/92
 
B15895
A

757 MAINTENANCE MANUAL
CLAMP  1.10
INCH
INSTALLATION  0.90
BLEED PLUG
FWD  ACTUATOR TRUCK POSITIONER 
LEFT GEAR OUTBOARD SHOWN (RIGHT GEAR INBOARD QUIVALENT) 
A 
0.90 1.10 INCH  CLAMP INSTALLATION 
BLEED PLUG  TRUCK POSITIONER ACTUATOR 

FWD
LEFT GEAR INBOARD SHOWN
(RIGHT GEAR OUTBOARD EQUIVALENT)

A

Main Landing Gear Truck Positioner Actuator Installation
Figure 401 (Sheet 2)

B15905
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. AIRPLANES WITH CLAMPS INSTALLED ú

 32-32-15
 ON HYDRAULIC LINES  ú ú 02 Page 403 ú Mar 20/97
 
A

757 MAINTENANCE MANUAL
 S 864-028
 (4)  
Remove electrical power (AMM 24-22-00/201).

 E.
Procedure to Remove the Main Landing Gear Truck Positioner Actuator

 S 034-024
 (1)  
POSITIONER ACTUATOR WITH CLAMP; remove the clamp that holds the hydraulic lines from the positioner actuator.

 S 034-004

 (2)  
Disconnect the hydraulic lines from the actuator. Install plugs in the lines and fittings.

 S 014-030

 (3)  
Do these steps to permit removal of the pin from the rod end of the actuator (Fig. 402):

 (a)  
Remove the bolts which hold the cover to the J-1 junction box

 NOTE: The junction box is on the aft end of the truck beam of
____
 the main gear.

 (b)  
Put a tag with the color code and the pin locations on the sensor wires

 (c)  
Use a pin extraction tool, to remove the sensor wire from the terminal block in the junction box

 (d)  
Put a line on the sensor wires to make the installation easier

 (e)  
Disconnect the conduit coupling nut from the junction box

 (f)  
Remove or loosen the clamp that attaches the conduit to the truck beam

 (g)  
Move the conduit to permit removal of the pin.

 S 034-005
 (4)  Remove pin (1) to disconnect the rod end of the actuator from the truck beam (View A-A).
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：757 AMM 飛機維護手冊 起落架 CHAPTER 32 - LANDING GEAR 2(59)