S 014-014

 (4)  
Move the spring on the support shafts for the spring.

 (a)  
Remove the spring extender.

 S 414-015
 (5)
Install the end cap on the support shaft for the aft spring.

 (a)
Install the bolt, the washer, and the nut (View A-A).

 32-21-15
 ALL  ú ú 01 Page 404 ú Jan 28/00
 
A

757 
MAINTENANCE MANUAL
 S 414-016
 (6)  Install the tang washer and the nut on the support shaft for the
 forward spring (View B-B).
 (a)  Install the cotter pin.
 F.  Put the Airplane Back to Its Usual Condition
 S 094-019
 ú  WARNING:_______ OBEY THE REMOVAL PROCEDURE FOR THE DOOR LOCKS.  THE DOORS OPEN
 ú  AND CLOSE QUICKLY.  THE MOVEMENT OF THE DOORS CAN CAUSE
 ú  INJURIES TO PERSONS AND DAMAGE TO EQUIPMENT.
 ú
 (1)  Remove the door locks from the landing gear and close the doors
 (Ref 32-00-15).

 32-21-15
 ALL  ú ú 01.1 Page 405 ú Sep 28/02
 
A

1.

2.

ú
ú
ú

757 MAINTENANCE MANUAL
 NLG SHOCK STRUT INNER CYLINDER - REMOVAL/INSTALLATION
_____________________________________________________
General
_______
 A.  This procedure contains two tasks. The first removes the NLG inner cylinder. Task two installs the NLG inner cylinder.
 TASK 32-21-24-794-001
NLG Inner Cylinder Removal (Fig. 401)

__________________________

 A.  Equipment
 (1)  
Axle Jack - automotive type (Commercially
 available)

 (2)  
Lower Bearing Seal Retainer Puller Equipment,
 NLG - B32024-82

 (3)  
Gland Nut Wrench Adapter, NLG - A32045-19

 (4)  
Drain Equipment - MLG/NLG Shock Strut, A32066-1

 (5)  
Container

 B.  
References

 (1)  
AMM 07-11-02/201, Jacking Airplane Nose

 (2)  
AMM 29-11-00/201, Main Hydraulic Systems

 (3)  
AMM 32-00-15/201, Landing Gear Door Locks

 (4)  
AMM 32-00-20/201, Landing Gear Downlocks

 (5)  
AMM 32-21-09/401, Nose Gear Torsion Links

 C.  
Access

 (1)  
Location Zones
 711 Nose Landing Gear (NLG)
 713/714 NLG Door Forward
 715/716 NLG Door Aft

 D.  
Prepare to Remove the Inner Cylinder

 S 494-002
 (1)  Make sure the downlocks are installed on the nose and main landing gear (AMM 32-00-20/201).
 S 494-003
WARNING:_______OBEY THE INSTALLATION PROCEDURE FOR THE DOOR LOCKS. THE DOORSOPEN AND CLOSE QUICKLY. THE MOVEMENT OF THE DOORS CAN CAUSEINJURIES TO PERSONS AND DAMAGE TO EQUIPMENT.
 (2)  
Open the doors for the nose landing gear and install the door locks (AMM 32-00-15/201).

 S 864-005

 (3)  
Remove the pressure from the left hydraulic system reservoir (AMM 29-11-00/201).

 32-21-24
 ALL  ú ú 01.1 Page 401 ú Sep 28/02
 
A

757
MAINTENANCE MANUAL

SEE A
A
METERING PIN
SHOCK STRUT  (REF)
(REF)
A
UPPER CENTERING CAM OUTER
CYLINDER
INNER
AIR VALVE CYLINDER
CAP
SEE B
SWIVEL NUT LOWER CENTERING CAM RETAINER PIN
AIR VALVE
CAP
A
SWIVEL NUT SEE C
OIL CHARGING VALVE
OIL CHARGING VALVE
B

A-A
Nose Landing Gear Shock Strut Inner Cylinder - Removal
Figure 401 (Sheet 1)

G02777
 

 32-21-24
 ALL  ú ú 01 Page 402 ú Sep 20/96
 
A

757
MAINTENANCE MANUAL

UPPER STEERING
SUPPORT PLATE

LOWER STEERING
INNERSUPPORT PLATE
STEERING NUT
BOLT (2 LOCATIONS) ASSEMBLY

GLAND
NUT  RETAINER

BEARING PULLER
Nose Landing Gear Shock Inner Cylinder - Removal
Figure 401 (Sheet 2)

G02779
 

 32-21-24
 ALL  ú ú 01 Page 403 ú Sep 20/96
 
A

757
MAINTENANCE MANUAL
　
中國航空網(wǎng) m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：757 AMM 飛機維護(hù)手冊 起落架 CHAPTER 32 - LANDING GEAR 2(10)