NOTE: Push the pedals to the stops in 1 second, hold in for
____ 1 second, and release in 1 second. Wait 5 seconds seconds between each time that you push in and release the brake pedals.
(c) Make sure that the BRAKE PRESS gage indication is at least 1200 psig.
S 735-050
(10)
Do a test of the Alternate System Braking
(a)
Push in and release brake pedals a minimum of 6 times until the pressure shows on the BRAKE PRESS gage does not decrease any more with brake pedal operation.
(b)
Pressurize the left hydraulic system and reservoir (AMM 29-11-00/201).
(c)
Measure the brake pedal force and travel for each brake pedal. Make sure that each pedal meets the requirements in Table 3. 1) Attach a protractor to the brake pedal to measure the
travel.
2) Attach a spring scale to the brake pedal to measure the
pedal force. ~.............................................................................. | Table 3 | ................................................................................ | *[1] | *[2] | ................................................................................ | | Brake Pedal | Brake Pedal | Brake | Brake Pedal | | Pedals | Travel (DEG) | Force (LBS) |Pressure (PSIG) | Force (LBS) | ................................................................................ |Captain's, | | | | | |First Officer's | 5 Maximum | 29 (|3) | 500 (|50) | 43.6 (|4.6) | ................................................................................ |Captain's, | | | | | |First Officer's | 12 Maximum | 64 (|4) | 2800 (|50) | 96 (|6) | 2................…..............….............…................…...............1
*[1] The pedal force must be measured by the load applied
perpendicular to the tip of the pedal, 8.4 inches from the pivot.
The brake pressure is the value shown at each wheel brake gage.
*[2] The brake pedal force measured using the J32001-39 equipment. The
load on the J32001 is located 5.58 inches from the pedal pivot.
(d)
Make sure that the pressure indication at each wheel brake is not more than 75 psig after you release the brake.
(e)
Push in and hold the Captain's brake pedals against the stops.
32-41-00
ALL ú ú 01A Page 520 ú May 28/01
A
757
MAINTENANCE MANUAL
(f)
Make sure that the brake pressure shown at each wheel brake gage is within 200 psig of the system supplied pressure (2850 to 3150 psig).
(g)
Look at the wear indicator pin on each brake to make sure that each brake has set.
(h)
Release the brake pedals.
(i)
Make sure that the pressure at each brake is not more than 75 psig.
(j)
Look at the wear indicator pin on each brake to make sure that each brake has released correctly.
(k)
Repeat steps (d) thru (i) with the First Officer's brake pedals.
S 735-053
(11) Do a test of the Automatic Wheel Brake (Gear Retraction Braking) Operation
S 495-082
WARNING: MAKE SURE THE DOWNLOCKS ARE INSTALLED ON THE NOSE AND MAIN
_______ LANDING GEAR BEFORE YOU MOVE THE CONTROL LEVER FOR THE LANDING GEAR. IF THE CONTROL LEVER IS MOVED WITHOUT THE DOWNLOCKS INSTALLED, THE LANDING GEAR CAN RETRACT AND CAUSE INJURY TO PERSONS OR DAMAGE TO EQUIPMENT.
(12) Make sure the downlocks are installed in the nose and main landing gear (AMM 32-00-20/201).
S 325-094
WARNING: USE THE PROCEDURE IN AMM 32-00-15/201 TO INSTALL THE DOOR
_______ LOCKS. DOORS OPEN AND CLOSE QUICKLY AND CAN CAUSE INJURY TO PERSONS OR DAMAGE TO EQUIPMENT.
(13)
Open the doors for the main landing gear and install the door locks (AMM 32-00-15/201).
(a)
Put chocks on the wheels.
S 865-054
(14)
Pressurize the left and right hydraulic systems and reservoirs (AMM 29-11-00/201).
S 735-055
(15)
Continue the test.
(a)
Push the manual override button on the landing gear control panel and move the landing gear control handle to the UP position.
(b)
Make sure that the pressure at each wheel brake gage is 450 to 880 psig.
(c)
Move the landing gear control handle to the DN position.
32-41-00
ALL ú ú 01A Page 521 ú May 28/01
A
757
MAINTENANCE MANUAL
S 735-057
(16)
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：757 AMM 飛機維護手冊 起落架 CHAPTER 32 - LANDING GEAR 2(143)
