S 864-021

 (4)  
Remove the power from the left hydraulic system if it is not necessary (AMM 29-11-00/201).

 32-32-07
 ALL  ú ú 01 Page 405 ú May 28/99
 
A

757 MAINTENANCE MANUAL
 MAIN GEAR UPLOCK-OPERATED SEQUENCE VALVE - REMOVAL/INSTALLATION
_______________________________________________________________
 1.  General_______
 A.  This procedure has two tasks. The first task is for removal of the uplock-operated door sequence valve for the main landing gear. The other task is for installation of the door sequence valve.
 TASK 32-32-09-004-001
 2.  Remove the Uplock-Operated Door Sequence Valve for the Main Landing Gear________________________________________________________________________ (Fig. 401)
 A.  References
 (1)  
AMM 29-11-00/201, Pressurize/Depressurize Main Hydraulic System

 (2)  
AMM 32-00-15/201, Landing Gear Door Locks

 (3)  
AMM 32-00-20/201, Landing Gear Downlocks

 B.  
Access

 (1)  
Location Zones
 143 MLG Wheel Well (Left)
 144 MLG Wheel Well (Right)

 C.  
Prepare for Removal

 S 214-002
 (1)  Make sure the downlocks are installed on the nose and main landing gear (AMM 32-00-20/201).
 S 494-003
 WARNING: USE THE PROCEDURE IN AMM 32-00-15/201 TO INSTALL THE DOOR
_______ LOCKS. THE DOORS OPEN AND CLOSE QUICKLY AND CAN CAUSE INJURY TO PERSONS OR DAMAGE TO EQUIPMENT.
 (2)  
Open the doors for the landing gear and install the door locks (AMM 32-00-15/201).

 S 864-004

 (3)  
Remove the pressure from the left hydraulic system and the hydraulic reservoir (AMM 29-11-00/201).

 32-32-09
 ALL  ú ú 01 Page 401 ú May 28/99
 
A

757 MAINTENANCE MANUAL
SEE A
UPLOCK-OPERATED SEQUENCE VALVE
BOLT (4 LOCATIONS)
UNION (5 LOCATIONS)
RESTRICTOR
CHECK VALVE

BOLT
LINK
ROD
UPLOCK ASSEMBLY
A
Main Landing Gear Uplock-Operated Sequence Valve Installation Figure 401

 32-32-09
 ALL  ú ú 01 Page 402 ú May 28/99
 
A

757 MAINTENANCE MANUAL
 D. Remove the Door Sequence Valve
 S 034-005
 (1)  
Disconnect the hydraulic lines from the sequence valve.

 S 494-006

 (2)  
Install plugs in the lines and fittings.

 S 034-007

 (3)  
Remove the bolt to disconnect the link from the sequence valve (Detail A).

 S 034-008

 (4)  
Remove the bolts that attach the sequence valve to the uplock assembly and bracket.

 S 024-009

 (5)  
Remove the sequence valve.

 TASK 32-32-09-404-020
 3.  Install the Sequence Valve for the Main Landing Gear (Fig. 401)____________________________________________________
 A. Consumable Materials
 (1)  
D00148 Hydraulic Fluid - BMS 3-11, Type IV,
 Class 1

 (2)  
D00054 Hydraulic Lubricant - MCS 352

 B.
References

 (1)  
AMM 12-12-01/301, Hydraulic Systems

 (2)  
AMM 29-11-00/201, Pressurize/Depressurize Main Hydraulic System

 (3)  
AMM 32-00-15/201, Landing Gear Door Locks

 C.
Access

 (1)  
Location Zones
 143 MLG Wheel Well (Left)
 144 MLG Wheel Well (Right

 D.
Procedure to Install the Sequence Valve

 S 434-021
 (1)  
If the unions, restrictor, and packing are not installed in the valve, do the steps that follow:

 (a)  
Apply a thin layer of BMS 3-11 fluid or MCS 352 lubricant to the unions, restrictor, and packing.

 (b)  
Install the unions, restrictor, and packing in the valve ports.

 32-32-09
 ALL  ú ú 01 Page 403 ú May 28/99
 
A

757
MAINTENANCE MANUAL

 S 424-010
 (2)  Install the bolts, washers, bushing, and nuts to attach the sequence valve to the uplock assembly and bracket (Detail A). Install with the bolt head away from the valve. Install the washers behind both the bolt head and the nut.
 NOTE: Install the bushing with the bottom right bolt only.
____
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：757 AMM 飛機維護手冊 起落架 CHAPTER 32 - LANDING GEAR 2(55)