77-40-00
AMM
Detail Steps/Work Items Key Items/References
(10) Do a test of the fuel flow indicating system: S Monitor the fuel flow indicator. S Set the ALT/BAT switch to ON. S Do an engine ground run-up. S Shut down the engine. The indicator must read zero. Refer to the DA 40 Airplane Flight Manual. The indicator must show the relevant fuel flow.
C. Replace the Cylinder Head Temperature (CHT) Probe
Detail Steps/Work Items Key Items/References
WARNING: MAKE SURE THE ENGINE IS SAFE BEFORE YOU DO ANY WORK ON IT. IF THE ENGINE STARTS THE PROPELLER CAN CAUSE INJURY OR DEATH.
(1) Make sure that the engine is safe: S The ignition switch is set to OFF. S Set the ALT/BAT switch to OFF. S The throttle is set to IDLE. S The mixture control is set to LEAN CUT-OFF.
(2) Remove the engine top-cowling. Refer to Section 71-10.
(3) Disconnect the airplane battery. Refer to Section 24-31.
(4) Disconnect the electrical cables from the temperature probe. Refer to Figure 4. At the in-line connector.
(5) Replace the CHT probe: S Unscrew the probe from the cylinder head. S Move the probe clear of the airplane. S Install the new probe.
(6) Connect the electrical cables to the probe. At the in-line connector.
(7) Connect the airplane battery. Refer to Section 24-31.
(8) Install the engine cowlings. Refer to Section 71-10.
Page 206 Doc # 6.02.01 09 Jan 2003 Rev. 4
77-40-00
Engine Indicating
AMM
Detail Steps/Work Items Key Items/References
(9) Do a test of the CHT indicating system: S Monitor the CHT indicator. S Set the ALT/BAT Switch to ON. S Do a ground run-up of the engine. The indicator must show zero. The indicator must show the ambient temperature of the cylinder head. Refer to the DA 40 Airplane Flight Manual. The CHT indicator must show the relevant temperature.
D. Replace an Exhaust Gas Temperature (EGT) Probe
Detail Steps/Work Items Key Items/References
WARNING: MAKE SURE THE ENGINE IS SAFE BEFORE YOU DO ANY WORK ON IT. IF THE ENGINE STARTS THE PROPELLER CAN CAUSE INJURY OR DEATH.
(1) Make sure that the engine is safe: S The ignition switch is set to OFF. S Set the ALT/BAT switch to OFF. S The throttle is set to IDLE. S The mixture control is set to LEAN CUT-OFF.
(2) Remove the engine cowlings. Refer to Section 71-10.
(3) Disconnect the airplane battery. Refer to Section 24-31.
(4) Disconnect the electrical cables from the EGT probe. Refer to Figure 5. At the in-line connector.
(5) Replace the EGT probe: S Release the worm drive clamp which holds the EGT probe in position. S Replace the EGT probe. S Install the worm drive clamp which holds the EGT probe.
Doc # 6.02.01 Page 207
Rev. 4 09 Jan 2003
77-40-00
AMM
DA 40 Series
Detail Steps/Work Items Key Items/References
(6) Connect the electrical cables to the EGT probe. At the in-line connector.
(7) Connect the airplane battery. Refer to Section 24-31.
(8) Install the engine cowlings. Refer to Section 71-10.
(9) Do a test of the EGT indicating system: S Monitor the EGT indicator. S Set the ALT/BAT Switch to ON. S Do an engine ground run-up. The indicator must show zero. The indicator must show the ambient temperature of the cylinder head. Refer to the DA 40 Airplane Flight Manual. The EGT indicator must show the relevant temperature.
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：鉆石40飛機維護手冊 DA 40 SERIES AMM 6(5)
