Doc # 6.02.01 Page 201
Rev. 4 09 Jan 2003
33-40-00
AMM
B. Install the Taxi Light
DA 40 Series
Detail Steps/Work Items Key Items/References
(1) Hold the taxi light in position in the leading edge of the left wing. S Connect the electrical connector to the rear of the taxi light.
(2) Install the screws which attach the taxi light assembly to the wing.
(3) Set the ALT/BAT switch (Lycoming version) or ELECTRIC MASTER key switch (TAE version) to ON.
(4) Set the TAXI/MAP circuit -breaker Closed
(5) Set the TAXI light switch to ON.
(6) Set the TAXI light switch to OFF.
(7) Set the ALT/BAT switch (Lycoming version) or ELECTRIC MASTER key switch (TAE version) to OFF.
(8) Install the taxi/landing light cover to the wing: S Put the light cover in position on the wing. S Install the 12 screws which attach the light cover to the wing.
%
%
%
%
3. Remove/Install the Landing Light
A. Remove the Landing Light
%
%
Detail Steps/Work Items Key Items/References
(1) Set the ALT/BAT switch (Lycoming version) or ELECTRIC MASTER key switch (TAE version) to OFF.
(2) Set the LANDING light switch to OFF.
(3) Set the LANDING circuit -breaker open.
(4) Remove the taxi/landing light cover from the wing: S Remove the 12 screws which attach the light cover to the wing. S Pull the light cover clear of the wing.
Page 202 Doc # 6.02.01 09 Jan 2003 Rev. 4
33-40-00
Lights
AMM
Detail Steps/Work Items Key Items/References
(5) Remove the screws which attach the landing light to the wing. The landing light is the inboard assembly. Refer Figure 2.
(6) Hold the landing light and carefully move the light out from the wing: S Disconnect the electrical connector from the rear of the landing light. S Remove the landing light.
B. Install the Landing Light
%
%
%
%
Detail Steps/Work Items Key Items/References
(1) Hold the taxi light in position in the leading edge of the left wing. S Connect the electrical connector to the rear of the taxi light.
(2) Install the screws which attach the taxi light assembly to the wing.
(3) Set the ALT/BAT switch (Lycoming version) or ELECTRIC MASTER key switch (TAE version) to ON.
(4) Set the LANDING circuit -breaker Closed
(5) Set the LANDING switch to ON.
(6) Set the LANDING light switch to OFF.
(7) Set the ALT/BAT switch (Lycoming version) or ELECTRIC MASTER key switch (TAE version) to OFF.
(8) Install the taxi/landing light cover to the wing: S Put the light cover in position on the wing. S Install the 12 screws which attach the light cover to the wing.
Doc # 6.02.01 Page 203
Rev. 4 09 Jan 2003
33-40-00
AMM
4. Replace a Filament in the Wing-Tip Light Unit
A. Replace a Position Light Filament in the Wing-Tip
%
%
Detail Steps/Work Items Key Items/References
(1) Set the ALT/BAT switch (Lycoming version) or ELECTRIC MASTER key switch (TAE version) to OFF.
WARNING: AFTER YOU SET THE POWER TO OFF, MAKE SURE THAT YOU WAIT A MINIMUM OF FIVE MINUTES BEFORE YOU DO WORK ON THE STROBE LIGHTS. THE POWER SUPPLIES TO THE STROBE LIGHTS GENERATE HIGH VOLTAGE. HIGH VOLTAGE CAN CAUSE DEATH OR INJURY TO PERSONS.
(2) Remove the light unit cover from the wing -tip and the lamp glasses. Refer to Figure 1.
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：鉆石40飛機維護手冊 DA 40 SERIES AMM 3(91)
