Doc # 6.02.01 Page 203
Rev. 4 09 Jan 2003
32-10-00
AMM
%
%
%
%
DA 40 Series
Detail Steps/Work Items Key Items/References
(11) Install the brake caliper. Refer to Section 32-40.
(12) Install the wheel. Refer to Section 32-40.
(13) Install the back-plate to the brake caliper. Refer to Section 32-40.
(14) Install the wheel fairing: S Install the outer bolt. S Install 4 screws on the inner side.
(15) Install the strut fairing: S Install strut fairing. S Install stub wing cover. S Install brake cover. Optional, see O.M 40-106. Take care of padding on strut. Take care of padding on strut cover.
(16) Lower the airplane with jacks. Refer to Section 07-10.
(17) Do a test for correct adjustment of the landing gear. See Paragraph 3.
(18) Do a function test of the wheel brake system.
32-10-00
Landing Gear
AMM
3. Test/Adjust the Main Landing Gear
Do this work at the following times: ) When required by the maintenance checklist (Chapter 05). ) After a hard landing. ) After any repair to the main landing gear strut.
A. Equipment
Item Quantity Part Number
Slide sheets - 2 per side. 4 Commercial.
Doc # 6.02.01 Page 205
Rev. 4 09 Jan 2003
32-10-00
AMM
Outer Face of Wheel
Figure 3: Measure Toe-In and Camber
Page 206 Doc # 6.02.01 09 Jan 2003 Rev. 4
32-10-00
Landing Gear
AMM
B. Procedure
%
%
%
%
DA 40 Series
Detail Steps/Work Items Key Items/References
(1) Make sure that the airplane is at the empty weight. See the Adjustment Report for the airplane.
(2) Remove the strut fairings, if installed: S Remove brake cover. S Remove stub wing cover. S Remove strut fairing. Optional, see O.M 40-106. Remove bolts and washers. Remove bolts and washers. Remove bolts and washers at the rear.
(3) Remove the wheel fairings: S Remove the outer bolt. S Remove 4 screws from the inner side. For each wheel.
(4) Move the airplane to put the main wheels on the slide sheets.
(5) Measure the toe-in. Refer to Figure 3.
(6) Measure the camber. Refer to Figure 3.
WARNING: USE ONLY THE SHIMS LISTED FOR THE PURPOSE IN THE ILLUSTRATED PARTS CATALOGUE. OTHER SHIMS COULD CAUSE LANDING GEAR FAILURE.
(7) If necessary, adjust the toe-in and/or camber. Refer to Chapter 06-00 for limits. Maximum 2° shim per side (camber + toe). See the Illustrated Parts Catalogue for the correct shims. Put shims between the strut and the axle. These change the angle between the axle and the airplane longitudinal or vertical axis.
(8) Measure the wheel track. Across the airplane from the outermost point on one axle to the outermost point on the other axle.
(9) Move the airplane off the slide sheets.
Doc # 6.02.01 Page 207
Rev. 4 09 Jan 2003
32-10-00
AMM
%
%
%
%
Detail Steps/Work Items Key Items/References
(10) Install the wheel fairings: S Install the outer bolt. S Install 4 screws on the inner side.
(11) Install the strut fairings: S Install strut fairing. S Install stub wing cover. S Install brake cover. Optional, see O.M 40-106. Take care of padding on strut. Take care of padding on strut cover.
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：鉆石40飛機維護手冊 DA 40 SERIES AMM 3(77)
