曝光臺 注意防騙 網曝天貓店富美金盛家居專營店坑蒙拐騙欺詐消費者

% Figure 2 shows the center console structure. Refer to the related Chapters for the data on the controls.
% The engine control assembly has two aluminum alloy side plates. Four brackets attach to the side % plates with rivets. The front bracket has holes to anchor the outer sheaths of the brake and heat % control cables. The top bracket has two anchor-nuts. Bolts engage the anchor nuts to attach the % engine control assembly to the top of the floor panel.
% The center bracket has two anchor nuts for the control cover plates. The rear bracket attaches to the % elevator trim control assembly.
% There are no user-maintainable parts in the engine control assembly structure.
Doc # 6.02.01 Page 5
Rev. 4 09 Jan 2003

31-11-00
AMM

% Intentionally left blank
31-11-00
Indicating Systems
AMM

% Trouble-Shooting % 1. General
% The table below lists the defects you could have with the control panel in the center console. If you % have the trouble detailed in the Trouble column read across to the Possible Cause column. Then do % the repair given in the Repair column.
%

%

%

%
%

%
%

%

Trouble  Possible Cause  Repair 
Parking brake or cabin heat control levers do not stay in the set position.  Friction tension too low. Too much wear in the friction washers.  Adjust the friction. Replace the friction washers. 

%

Doc # 6.02.01 Page 101
Rev. 4 09 Jan 2003

31-11-00
AMM

% Intentionally left blank
31-11-00
Indicating Systems
AMM

% Maintenance Practices % 1. General
% These maintenance practices tell you how to remove/install the engine control assembly. See the % related Chapter for data about indicators in other systems.
% 2. Remove/Install the Engine Control Assembly
% A. Remove the Engine Control Assembly % %

%
%
%
%
%

%

%
%

%
%
%

%

%
%

%
%

%

%

%
%

%
%

Detail Steps/Work Items  Key Items/References 
(1)  Remove the knob from the emergency fuel valve: S Remove the cross-head screw from the center of the control-knob and pull the knob up and off the fuel selector valve. S Remove the mounting plate. 
(2)  Remove the engine power control lever assembly.  Refer to Section 76-11. 
(3)  Remove the bolts that attach the engine control assembly to the floor panel at the front and at the rear. 
(4)  Remove the front cover plate. 
(5)  Move the engine control assembly to a position where you can reach the control cables. 
(6)  Disconnect the following control cables from the center console: S Cabin heat control cable. S Cabin heat distribution control cable. S Parking brake control cable.  Refer to Section 21-01. Refer to Section 21-01. Refer to Section 32-40. 
(7)  Move the engine control assembly clear of the airplane. 

%

Doc # 6.02.01 Page 201
Rev. 4 09 Jan 2003

31-11-00
DA 40 Series
AMM

%

%
%
%

%

%
%
%
%
%
%
%

%

%
%
%

%
%

%
%
%
%

%
%
%

% B. Install the Engine Control Assembly %

Detail Steps/Work Items  Key Items/References 
(1)  Make sure that there are no loose items, specially in the center console. 
(2)  Move the engine control assembly onto the center console and support it in a position where you can install the control cables. 
(3)  Connect these control cables to the engine control assembly: S Parking brake control cable. S Cabin heat distribution control cable. S Cabin heat control cable.  Refer to Section 32-40. Refer to Section 21-01. Refer to Section 21-01. 
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：鉆石40飛機維護手冊 DA 40 SERIES AMM 3(65)