曝光臺 注意防騙 網曝天貓店富美金盛家居專營店坑蒙拐騙欺詐消費者

Force or Weight Newton [N] Decanewton [daN] Pound [lb]  [N] / 4.448 = [lb] [daN] / 0.4448 = [lb]  [lb] x 4.448 = [N] [lb] x 0.4448 = [daN] 
Mass ('Weight') Kilogram [kg] Pound [lb]  [kg] / 0.45359 = [lb]  [lb] x 0.45359 = [kg] 
Volume Liter [l] US gallon [US gal] US quart [US qt] Imperial gallon [Imp gal] Cubic inch [in3]  [l] / 3.7854 = [US gal] [l] / 0.9464 = [US qts] [l] / 4.5459 = [Imp gal] [l] / 61.024 = [in3]  [US gal] x 3.7854 = [l] [US qt] x 0.9464 = [l] [Imp gal] x 4.5459 = [l] [in3] x 61.024 = [l] 
Torque Newton meter [Nm] Foot pound [ft.lb] Inch pound [in.lb]  [Nm] / 1.3558 = [ft.lb] [Nm] x 8.851 = [in.lb]  [ft.lb] x 1.3558 = [Nm] [in.lb] / 8.851 = [Nm] 
Temperature Degree Celsius [°C] Degree Fahrenheit [°F]  [°C] x 1.8 + 32 = [°F]  ([°F] - 32) / 1.8 = [°C] 

Note:  In this Airplane Maintenance Manual masses are referred to as weights. The authors accept that this is technically incorrect but have used the expression for simplicity and convenience.
Page 6 Doc # 6.02.01 09 Jan 2003 Rev. 4
02-00-00
Manual Organization
AMM

9. Torque Conversion Graphs
Use Figure 1 for conversion of torque values Nm - ft.lb. Use Figure 2 for conversion of Nm - in.lb.
Foot.Pound (ft.lb.)

70 65 60 55 50 45 40 35 30 25 20 15 10 5

Figure 1: Nm - ft.lb
Find the Nm value on the horizontal axis. Move vertically to the solid black diagonal line. Then move horizontally to the vertical axis. Read the value in ft.lb.
Example: To convert 24 Nm to ft.lb., find 24 Nm on the horizontal axis (see the dashed line). Follow the dashed line vertically to the solid black diagonal line. Then follow the dashed line horizontally to the vertical axis. Read the value of 17.7 ft.lb.
Doc # 6.02.01 Page 7
Rev. 4 09 Jan 2003

02-00-00
AMM

0 0.5 1.0 1.5 2.0 2.5 3.0 3.5 4.0 4.5 5.0 5.5 6.0 6.5 7.0 7.5 8.0 8.5 9.0 9.5 10.0

Newton.Metre (Nm)
Figure 2: Nm - in.lb
Find the Nm value on the horizontal axis. Move vertically to the solid black diagonal line. Then move horizontally to the vertical axis. Read the value in in.lb.
Example: To convert 4.4 Nm to in.lb, find 4.4 Nm on the horizontal axis (see the dashed line). Follow the dashed line vertically to the solid black diagonal line. Then follow the dashed line horizontally to the vertical axis. Read the value of 39 in.lb.
Page 8 Doc # 6.02.01 09 Jan 2003 Rev. 4
02-00-00
General Description
AMM

CHAPTER 03

GENERAL DESCRIPTION OF THE
AIRPLANE

Doc # 6.02.01 Page 1
Rev. 4 09 Jan 2003

03-TITLE
AMM

Intentionally left blank
03-TITLE
General Description
AMM

TABLE OF CONTENTS
CHAPTER 03
GENERAL DESCRIPTION OF THE AIRPLANE

1.
General ..............................................1

2.
Description............................................1

3.
Equipment Data........................................4

 

Doc # 6.02.01 Page 1
Rev. 4 09 Jan 2003

03-CONTENTS
AMM

Intentionally left blank
03-CONTENTS
General Description
AMM

CHAPTER 03
GENERAL DESCRIPTION OF THE AIRPLANE

1. General
Diamond Aircraft Industries GmbH, N. A. Otto-Stra.e 5, A-2700 Wiener Neustadt, Austria, make the DA 40 airplane.
2. Description
The DA 40 is a single-engine, four seat, low-wing monoplane. It has a cantilever wing and a ‘T’ tail.
The airplane structure is fiber-reinforced plastic composite. This gives a very strong but light structure.

Figure 1: DA 40 Airplane
Doc # 6.02.01 Page 1
Rev. 4 09 Jan 2003

03-00-00
AMM

The semi-monocoque fuselage is a glass-fiber reinforced-plastic (GFRP) shell with GFRP bulkheads and stiffeners. Uni-directional carbon fiber bands give extra strength and stiffness in many areas. Left and right half-shells bond together with a center section to make the fuselage. The center section makes the bottom of the cockpit. It has the main bulkheads which connect to the spars in each wing. The vertical stabilizer has two GFRP half-shells that are part of the fuselage shells.
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：鉆石40飛機維護手冊 DA 40 SERIES AMM 1(28)