(2)  
Access Panel
 413 and 414 Fan Cowl Panels - Engine 1
 417 and 418 Core Cowl Panels - Engine 1
 423 and 424 Fan Cowl Panels - Engine 2
 427 and 428 Core Cowl Panels - Engine 2
 433 and 434 Fan Cowl Panels - Engine 3
 437 and 438 Core Cowl Panels - Engine 3
 443 and 444 Fan Cowl Panels - Engine 4
 447 and 448 Core Cowl Panels - Engine 4
 451 Forward Fairing - Engine 1
 461 Forward Fairing - Engine 2
 471 Forward Fairing - Engine 3
 481 Forward Fairing - Engine 4

 G.
Install the Thrust Reverser (Fig. 401, Fig. 402)

 S 864-025-N00
 (1)  
Supply electrical power (AMM 24-22-00/201).

 S 494-026-N00

 (2)  
Attach the sling assembly (A71002) for the thrust reverser to the
 thrust reverser half at the forward and aft hoist points.

 (a)  Attach the tag lines to the thrust reverser.

 (3)  
Make sure the thread protectors are installed on all bolts.

 (4)  
Lubricate the shank of the bolts with the grease.

 S 494-027-N00
 S 644-066-N00
 NOTE: Do not let the grease get on the threads.
____
 S 034-070-N00
 (5)  Remove the plastic or wire ties from the center and aft hinge
 bearings.

 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 78-31-01
 ALL  ú ú N01 Page 412 ú Jun 18/01
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
S 434-028-N00
 (6)  If the link (14) attachment is necessary, install the link (14) with the bolt (12), washer (8) and nut (9).
 S 424-029-N00
 WARNING: DO NOT GET BELOW OR NEAR THE THRUST REVERSER WHEN YOU LIFT IT.
_______ INJURY TO PERSONS OR DAMAGE TO EQUIPMENT CAN OCCUR IF THE THRUST REVERSER FALLS OR MOVES.
 CAUTION: WHEN YOU CAREFULLY LIFT THE THRUST REVERSER, DO NOT LET THE
_______ THRUST REVERSER AND STRUT TOUCH. CONTROL THE MOVEMENT OF THE THRUST REVERSER WITH THE TAG LINES. IF THE THRUST REVERSER TOUCHES THE ENGINE OR OTHER EQUIPMENT, DAMAGE TO THE THRUST REVERSER CAN OCCUR.
 MAKE SURE THE TOP SKIRT FAIRING SUPPORTS DO NOT TOUCH THE STRUT. DAMAGE TO THE SUPPORTS CAN OCCUR.
 (7)  
Attach the hoist to the sling assembly.

 S 424-067-N00

 (8)  
Slowly lift the thrust reverser half into its position.

 NOTE: When you lift the thrust reverser, it will be in the air at
____
 an angle of approximately 45 degrees.

 (a)  Align the hinge fittings on the thrust reverser with the strut fittings.
 S 434-030-N00
 (9)  Install the hinge bolts for the thrust reverser with the steps that follow:
 NOTE:____The hinge bolts have a tight tolerance fit. The installation of the hinge bolts is easier if you correctly install the hoist and correctly operate the hoist control. Do not use the air hammers or rivet guns to install the hinge bolts.
 (a)  Manually install the bolt (7) in the center hinge from the aft side.
 NOTE: The thread protector will point in the forward
____ direction. Move the bolt at an angle to install it around the rib on the fitting of the fan duct hinge.
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 78-31-01
 ALL  ú ú N01 Page 413 ú Feb 18/00
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
////////////////////////A / PW4000 SERIES /747-400 / ENGINES/MAINTENANCE MANUAL ////////////////////////
(b)  Manually install the bolt (10) in the aft hinge from the
 forward side.

 NOTE: The thread protector will point to the rear.
____
 (c)  Manually install the bolt (11) in the forward hinge link
 nearest to the strut from the aft side.

 NOTE: The thread protector will point forward.
____
 S 024-081-N00
 (10)
 Remove the thread protectors from the aft hinge bolt.

 S 424-082-N00

 (11)
 Install the washer (8) and nut (9) on the aft hinge bolt.
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：747-400 AMM 飛機維護手冊 EXHAUST 1(71)