B. Standard Tools and Equipment
 (1)  Airplane Scales that can measure individual wheel weights
 C. References
 (1)  
AMM 09-11-00/201, Towing

 (2)  
AMM 12-15-03/301, Wing Landing Gear Shock Strut Servicing

 (3)  
AMM 12-15-04/301, Body Landing Gear Shock Strut Servicing

 (4)  
AMM 12-15-05/301, Nose Landing Gear Shock Strut Servicing

 (5)  
AMM 24-22-00/201, Manual Control (Apply Power)

 (6)  
AMM 27-51-00/201, Trailing Edge Flap System

 (7)  
AMM 27-81-00/201, Leading Edge Flap System

 (8)  
AMM 28-26-00/201, Defueling

 (9)  
AMM 29-11-00/201, Main Hydraulic Supply System

 (10)
 AMM 32-00-30/201, Landing Gear Door Locks

 (11)
 AMM 32-11-20/401, Wing Gear Positioning Actuator

 D. Access
 (1)  Location Zones
 118 Electrical and Electronics Compartment, RH
 715 Nose Landing Gear
 735 Wing Landing Gear, LH
 745 Wing Landing Gear, RH
 755 Body Landing Gear, LH
 765 Body Landing Gear, RH

 E. Find Load Sensor Zeros (Figure 501)
 S 865-143
 (1)  Before the airplane flies, use Mode-99 to set the WBC to 100% autozero mode:
 (a)  Put the WBC into Mode-99 operation: 1) Open the keyboard cover, and push the MODE key. Display shows ( ) (MODE= ) 2) Push 99 (the 9 key two times).
 Display shows ( ) (MODE= 99) 3) Push the ENTER key. Display shows (OK? ) (MODE= 99) 4) When the proper mode shows, push the YES key.
 Display shows (ENTR CAL) (CODE )
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 31-41-00
 ALL  ú ú 04S Page 503 ú Oct 18/01
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400
MAINTENANCE MANUAL

 (b)  Select the proper data set to edit:
 1)  When the display shows ENTR CAL CODE, push the decimal point key (.), the 9 key, and then the MODE key. Display shows (ENTR CAL) (CODE .9M)
 2) Push the ENTER key. Display shows (OK? CAL ) (CODE .9M) 3) When the display shows OK? CAL CODE .9M, push the YES key. Display shows (ENTER 99) (CODE )
 4)  When the display shows ENTER 99 CODE, push 747 (the 7 key, the 4 key, and the 7 key), and the ENTER key. Display shows (ENTER 99) (CODE 747)
 5)  When the display shows OK? CODE 747, push the YES key.
 Display shows ( EDIT) (ZERO? ) 6) When the display shows EDIT ZERO?, push the NO key. 7) When the display shows EDIT SPAN?, push the NO key. 8) When the display shows EDIT OFFSET?, push the NO key. 9) When the display shows EDIT CAL RES?, push the NO key. 10) When the display shows EDIT CAL WWT?, push the NO key. 11) When the display shows EDIT CAL CNT?, push the NO key. 12) When the display shows EDIT % AZ?, push the YES key.
 Display shows (%AZ FLAG) ( 50% OK?)
 (c)  Set the WBC for 100% autozero: 1) When the display shows %AZ FLAG 50% OK?, push the NO key. Display shows (%AZ FLAG) (100% OK?)
 2)  When the display shows %AZ FLAG 100% OK?, push the YES key. Display shows (WRITE IN) (PROGRESS) for approximately 8 seconds, then it shows ( EXIT (MODE 99?)
 3)  When EXIT MODE 99? shows, push the YES key. Display shows (PROCESS ) (COMPLETE) for approximately 8 seconds.
 NOTE: After one flight, the WBC automatically goes back to
____ the normal value of 50% autozero.
 S 865-190
 (2)  Before subsequent airplane flights, Find the LANDING MSTR count value using mode-97:
 (a)  
Push the MODE key.

 (b)  
Push the 9 key and then the 7 key.

 (c)  
Push the ENTER key.

 (d)  
When OK? MODE = 97 shows, push the YES key.

 (e)  
When the LANDING MSTR value shows, record the count.

 (f)  
Add (+) one to the LANDING MSTR count. This value is the LANDING count used to identify the 100 percent data in mode 98.

 (g)  
Push the RESET key to stop this mode. (The WBC shows PROCESS ABORTED.)

 (h)  
Close the keyboard cover.

 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：747-400 AMM 飛機維護手冊 指示/記錄系統 1(87)