EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 31-41-02
 ALL  ú ú 01 Page 403 ú Oct 10/93
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400
MAINTENANCE MANUAL

 PITCH ATTITUDE SENSOR - REMOVAL/INSTALLATION
____________________________________________
 1.  General
_______
 A.  There are three tasks in this procedure. The first task is the removal of the pitch attitude sensor (PAS). The second task is the installation of the PAS. The installation task includes a PAS calibration and a PAS test.
 B.  The PAS, T1454, is on a bracket on the forward bulkhead of the main equipment center. There is an electrical connector on the side of the PAS.
 C.  Shims align the PAS to the correct tolerance. The shims are bonded to the bracket. Make sure you do not accidentally remove the shims when you remove the PAS. If you accidentally remove the shims, install them into their correct positions when you install the PAS.
 TASK 31-41-03-004-039
 2.  Pitch Attitude Sensor Removal (Fig. 401)
_____________________________
 A.  Access
 (1)  Location Zone
 118 Electrical and Electronics Compartment

 B.  Procedure
 S 864-017
 (1)  Open these circuit breakers and attach DO-NOT-CLOSE tags:
 (a)  
P414 Power Distribution Center - Left 1) 414K20 WT & BAL

 (b)  
P415 Power Distribution Center - Right 1) 415G21 WBS CHB ALT

 S 024-037
 (2)  Remove the PAS:
 (a)  
Disconnect the electrical connector.

 (b)  
Remove the three screws.

 (c)  
Remove the PAS.

 TASK 31-41-03-404-035
 3.  Pitch Attitude Sensor Installation (Fig. 401)
__________________________________
 A.  General
 (1)  This task includes a calibration procedure for the new PAS. You must find the pitch attitude of the airplane and use the weight and balance computer (WBC) to put the pitch attitude into the new PAS.
 B.  References
 (1)  
AIPC 31-41-03 Fig. 1

 (2)  
AMM 08-00-00/201, Leveling and Weighing

 (3)  
AMM 24-22-00/201, Manual Control (Apply Power)

 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 31-41-03
 ALL  ú ú 12 Page 401 ú Feb 15/98
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400
MAINTENANCE MANUAL

Pitch Attitude Sensor Installation
Figure 401

EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 31-41-03
 ALL  ú ú 02 Page 402 ú Oct 10/94
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400
MAINTENANCE MANUAL

 C.  Access
 (1)  Location Zone
 118 Electrical and Electronics Compartment

 D.  Pitch Attitude Sensor Installation
 S 864-024
 (1)  Make sure these circuit breakers are open with DO-NOT-CLOSE tags attached:
 (a)  
P414 Power Distribution Center - Left
 1) 414K20 WT & BAL

 (b)  
P415 Power Distribution Center - Right
 1) 415G21 WBS CHB ALT

 S 424-038
 (2)  Install the PAS:
 (a)  
Put the PAS against the bracket.

 (b)  
Install the three screws.

 (c)  
Connect the electrical connector DT1454.

 S 864-031
 (3) Remove the DO-NOT-CLOSE tags and close these circuit breakers:
 (a)  
P414 Power Distribution Center - Left
 1) 414K20 WT & BAL

 (b)  
P415 Power Distribution Center - Right
 1) 415G21 WBS CHB ALT

 E.  Pitch Attitude Sensor Calibration
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：747-400 AMM 飛機維護手冊 指示/記錄系統 1(114)