(b)
Push the line select key adjacent to <ACMS.
(c)
Push the line select key adjacent to the prompt that causes the software part number to show (usually REPROGRAM, STATUS, or VERSIONS AND P/N).
(d)
Make sure the correct software part number shows.
1) If the part number is not correct, then do this task: ACMS Data Management Unit Software Installation (AMM 31-35-10/201) or replace the DMU.
S 715-304
(4) Do a software configuration check of the QAR and a test of QAR operation:
(a)
Make sure that an optical disk is installed in the QAR drive.
(b)
Do these steps to do a software configuration check of the QAR:
NOTE: You must know the correct software part number for the
____ QAR. For the QAR to be an approved installation, software with the correct part number must be installed.
1) Push the MODE switch on the QAR front panel.
2) Push the + switch until S/W Version shows on the QAR.
3) Push the SET switch.
4) Make sure that the correct software part number shows.
a) If the part number is not correct, then do this task: Quick Access Recorder (QAR) Software Installation (AMM 31-35-02/201) or replace the QAR with one that has the correct software.
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
31-35-00
ALL ú ú 03 Page 502 ú Feb 18/00
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400 MAINTENANCE MANUAL
(c) Do a test of QAR operation: 1) Push the MODE switch on the front of the QAR. 2) Push the + or - switch on the QAR until 1 ACQUISITION shows
on the QAR display. 3) Push the SET switch on the QAR. 4) Push the MENU key on the center CDU. 5) Push the line select key adjacent to <ACMS. 6) Push the line select key adjacent to <DEVICE INTERFACES. 7) Push the line select key adjacent to <QAR. 8) Push the line select key adjacent to <START QAR.
a) Make sure that the QAR display shows RAW:XXXXX:YYYYY (where XXXXX is the input subframe counter and YYYYY is the record data subframe counter).
b) Make sure that the input subframe counter (XXXXX value)
increases. 9) Push the line select key adjacent to <STOP QAR. 10) Push the MODE switch on the QAR. 11) Push the - switch until the QAR shows 0 Annunciations. 12) Push the SET switch. 13) Make sure that OQAR Ready shows on the QAR display.
(d) Do a check of the QAR disk status:
1) Push the line select key adjacent to <QAR STATUS. a) Make sure that the CDU shows this: STATUS OK. b) Make sure that the CDU shows this: TAPE LOW NOTLOW.
2) Push the MENU key on the CDU.
TASK 31-35-00-745-042
3. Ground Test - Airplane Condition Monitoring System
__________________________________________________
A. General
(1) The CMCS ground test of the Airplane Condition Monitoring System (ACMS) puts the ACMS Data Management Unit (DMU) into the test mode. When the DMU completes the test, it sends the results back to the CMC.
B. References
(1)
AMM 24-22-00/201, Manual Control
(2)
AMM 31-35-01/401, ACMS Data Management Unit
(3)
AMM 32-09-02/201, Air/Ground Relays
(4)
AMM 34-61-02/401, Control Display Unit
(5)
AMM 45-10-00/501, Central Maintenance Computer System
C. Access
(1) Location Zones
221 Control Cabin, LH
222 Control Cabin, RH
D. Preconditions
S 865-171
(1) These conditions are necessary for this task:
(a)
Electrical power on (AMM 24-22-00/201).
(b)
DMU installed (AMM 31-35-01/401).
(c)
Airplane must be in the ground mode (AMM 32-09-02/201).
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：747-400 AMM 飛機維護手冊 指示/記錄系統 1(69)
