曝光臺 注意防騙 網曝天貓店富美金盛家居專營店坑蒙拐騙欺詐消費者

 ú
 ú  S 114-029-C00
 ú 
        ú
 WARNING:_______ DO NOT GET METHYL ETHYL KETONE (MEK) IN YOUR MOUTH OR EYES, OR
 ú  ON YOUR SKIN.  DO NOT BREATHE THE FUMES FROM MEK.  PUT ON A
 ú  PROTECTIVE SPLASH GOGGLE AND GLOVES WHEN YOU USE MEK.  KEEP MEK
 ú  AWAY FROM SPARKS, FLAME AND HEAT.  MEK IS A POISONOUS AND
 ú  FLAMMABLE SOLVENT WHICH CAN CAUSE INJURIES TO PERSONS OR DAMAGE
 ú  TO EQUIPMENT.
 ú
 ú  (6)  ENGINES PRE-CFMI-SB 75-007;
 ú  Clean the threads and flat areas of the cable conduit with MEK
 ú  solvent and a soft bristled brush.
 S 434-026-C00
 (7)  Carefully put the part of the conduit cap with threads into the
 slotted mounting bracket.
 ú  (a)  ENGINES PRE-CFMI-SB 72-412 OR ENGINES WITH ONE WASHER BETWEEN
 ú  THE CONDUIT CAP AND THE NOSE CAP;
 Install the washer on the nose cap side of the bracket.
 ú  (b)  ENGINES POST-CFMI-SB 72-412 OR ENGINES WITH TWO WASHERS BETWEEN
 THE CONDUIT CAP AND THE NOSE CAP;
 ú  Install one washer on the conduit cap side of the bracket.
 ú  Install the second washer on the nose cap side of the bracket.

 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 75-31-02
 ALL  ú ú C02.1 Page 407 ú Jul 12/02
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
////////////////////////A / /
CFM56 ENGINES
737-300/400/500/ /MAINTENANCE MANUAL ////////////////////////
ú (c) ENGINES POST-CFMI-SB 72-950; ú Engines with this service bulletin do not use washers.
 S 434-031-C00
 (8)  Install the nose cap and the support tube assembly.
 S 434-038-C00
 CAUTION: USE TWO WRENCHES WHEN YOU TIGHTEN THE NOSE CAP TO HOLD THE
_______ CABLE. IF YOU PERMIT THE CABLE TO TURN, DAMAGE TO THE CABLE CAN OCCUR.
 USE ONE WRENCH ON THE CONDUIT CAP AND ONE WRENCH ON THE NOSE CAP.
 (9)  Tighten the nose cap to 180-200 pound-inches
 (20-22.5 Newton meters).

 (a)  Safety the nose cap with a lockwire.
 S 424-039-C00
 (10)
 Move the cable into the rubber packing block at the 6:30 o'clock position.

 S 434-040-C00

 (11)
 Install the three clamps that attach the MEC end of the feedback cable as follows:

 (a)  
Install the clamp bushings and inner and outer spring clips on the cable.

 (b)  
Lubricate the bolt threads with grease.

 (c)  
Attach the clamp to the 6 o'clock strut bracket of the fan frame with the bolt and nut (1 location).

 (d)  
Attach the clamps to the 6:30 and 7 o'clock rear flange brackets of the fan frame with the bolts and nuts (1 each).

 (e)  
Tighten the bolts to 100-110 pound-inches (11.3-12.4 Newton meters).

 

 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 75-31-02
 ALL  ú ú C01.1 Page 408 ú Jul 12/02
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
////////////////////////A / /
CFM56 ENGINES
737-300/400/500/ /MAINTENANCE MANUAL ////////////////////////
S 434-041-C00
 CAUTION:_______ THE CABLE INNER PART MUST BE IN THE FULLY RETRACTED POSITION WHEN YOU REMOVE THE SUPPORT TUBE AND NOSE CAP. IF THE CABLE INNER PART IS NOT IN THE RETRACTED POSITION, DAMAGE TO THE POLISHED INNER PART OF THE CABLE CAN OCCUR.
 DO NOT REMOVE THE SUPPORT TUBE FROM EACH END OF THE CABLE AT THE SAME TIME.
 (12) Move the cable inner part to the fully retracted position at the bellcrank end.
 S 034-042-C00 (13) Remove the nose cap from the conduit cap at the bellcrank end.
 ú ú ú ú ú  S 434-043-C00 (14) Carefully install the part of the conduit cap with threads into theslotted mounting bracket.(a) ENGINES PRE-CFMI-SB 72-412 OR ENGINES WITH ONE WASHER BETWEEN THE CONDUIT CAP AND THE NOSE CAP; Install the washer on the nose cap side of the bracket.(b) ENGINES POST-CFMI-SB 72-412 OR ENGINES WITH TWO WASHERS BETWEEN THE CONDUIT CAP AND THE NOSE CAP; Install one washer on the conduit cap side of the bracket. Install the second washer on the nose cap side of the bracket.(c) ENGINES POST-CFMI-SB 72-950;Engines with this service bulletin do not use washers.
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：737-300 400 500 AMM 飛機維護手冊 空氣 AIR(61)