(2)
D00579
B. References
(1)
AMM 71-11-02/201, Fan Cowl Panels
(2)
AMM 78-31-00/201, Thrust Reverser
C. Access
(1)
Location Zones
506 Engine No. 1
606 Engine No. 2
(2)
Access Panels 5739L/5738L Engine No. 1 - Thrust Reverser Half 5839R/5838R Engine No. 2 - Thrust Reverser Half
D. Procedure (Fig. 601)
S 016-010-C00
(1) Open the right fan cowl panel (AMM 71-11-02/201).
S 016-011-C00
WARNING: OBEY THE INSTRUCTIONS IN THE PROCEDURE TO OPEN THE THRUST
_______ REVERSERS. IF YOU DO NOT OBEY THE INSTRUCTIONS WHEN YOU OPEN THE THRUST REVERSERS, INJURIES TO PERSONS OR DAMAGE TO EQUIPMENT CAN OCCUR.
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
75-24-01
ALL ú ú C01 Page 601 ú Jul 15/97
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
////////////////////////A / /
CFM56 ENGINES
737-300/400/500/ /MAINTENANCE MANUAL ////////////////////////
(2)
Open the right thrust reverser half (AMM 78-31-00/201).
S 216-003-C00
(3)
Examine the valve housing for:
(a)
Cracks - make a visual inspection
1) If there are cracks, replace the valve.
(b)
Deformation
1) If there is deformation, replace the valve.
(c)
Nicks and scratches
1) All nicks and scratches are permitted.
S 216-004-C00
(4) Examine the flange joints for:
(a)
Loose bolts or nuts
1) Tighten the bolts to 'A' 24-27 pound-inches
(2.7-3.1 Newton meters) as necessary (Fig. 601).
2) Tighten the bolts to 'B' 55-70 pound-inches
(6.2-7.9 Newton meters) as necessary (Fig. 601).
3) Tighten the bolts to 'C' 100-130 pound-inches
(11.3-14.6 Newton meters) as necessary (Fig. 601). 4) Safety the bolts with a lockwire.
(b)
Sign of an air leakage at the 5th- and 9th- stage flanges. 1) If there is a leak, replace the gasket.
(c)
Cracks - make a visual inspection
1) If there are cracks, replace the valve.
(d)
Deformation or bends 1) If there are deformations or bends, replace the valve.
(e)
Sign of fuel leakage 1) If there is leakage at the forward flange, replace the gasket. 2) If there is leakage at the actuator covers, replace the valve.
3) If there is leakage at the actuator rod seals, replace the valve.
S 226-005-C00
(5) Examine the linkage for:
(a) Uniballs that will not move freely
1) Lubricate all around each uniball with 3-4 drops of LPS-1 penetrating oil. a) Let the uniballs soak in the lubrication for 2-3
minutes.
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
75-24-01
ALL ú ú C01 Page 602 ú Jul 15/94
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
////////////////////////A / /
CFM56 ENGINES
737-300/400/500/ /MAINTENANCE MANUAL ////////////////////////
SEE A
BLEED AIR 5TH-STAGE HPC FLANGE
COVER ACTUATOR
FLANGE BLEED AIR TUBE 9TH-STAGE HPC B
A SHAFTS BUTTERFLY B FLANGE FORWARD C CONTROL VALVE HPT CLEARANCE
B A
UNIBALLS
B
ACTUATOR VALVE RODS
FWD
A
High Pressure Turbine (HPT) Clearance Control Valve Inspection Figure 601
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：737-300 400 500 AMM 飛機維護手冊 空氣 AIR(16)
