(b)  
Tighten the bolts to 100-110 pound-inches
 (11.3-12.4 Newton meters).

 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 75-32-05
 ALL  ú ú C01 Page 407 ú Nov 15/93
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
////////////////////////A / /
CFM56 ENGINES
737-300/400/500/ /MAINTENANCE MANUAL ////////////////////////
S 824-024-C00
 (4)  If the locking bolt on the MEC adjustment bracket is not in the center position, do the step that follows:
 (a)  Loosen the locking bolt and turn the adjustment screw.
 S 034-025-C00
 CAUTION: PUT THE CABLE INNER MEMBER IN THE FULLY RETRACTED POSITION WHEN
_______ THE SUPPORT TUBE AND NOSE CAP ARE REMOVED. THIS IS TO PREVENT DAMAGE TO THE POLISHED INNER SURFACE. DO NOT REMOVE THE SUPPORT TUBE FROM THE TWO ENDS OF THE CABLE AT THE SAME TIME.
 (5)  
Remove the nose cap from the conduit cap at the MEC end.

 S 644-026-C00

 (6)  
Lubricate the conduit cap threads with grease.

 S 434-027-C00

 (7)  
Carefully put the threaded part of the conduit cap into the slotted retaining bracket.

 S 434-028-C00

 (8)  
Turn the nose cap on the conduit cap.

 S 434-029-C00

 (9)  
Tighten the nose cap by hand.

 S 424-030-C00

 (10)
 Move the cable into the rubber packing block found at the 6:30 o'clock position.

 S 434-031-C00

 (11)
 Install the three clamps that attach the MEC end of the feedback cable as follows:

 (a)  Install the clamp bushings and inner and outer spring clips on the cable.
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 75-32-05
 ALL  ú ú C01 Page 408 ú Jul 15/92
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
////////////////////////A / /
CFM56 ENGINES
737-300/400/500/ /MAINTENANCE MANUAL ////////////////////////
S 644-032-C00
 (12) Lightly lubricate the bolt threads with grease.
 (a)  
Attach clamps to the 6 o'clock strut bracket.

 NOTE:____Use one bolt and one nut each. Tighten the bolts by hand.

 (b)  
Attach clamps to the 6:30 and 7 o'clock rear flange brackets of the fan frame.

 NOTE:____Use one bolt and one nut each. Tighten the bolts by hand.
 S 864-033-C00
 CAUTION: PUT THE CABLE INNER MEMBER IN THE FULLY RETRACTED POSITION WHEN
_______ THE SUPPORT TUBE AND NOSE CAP ARE REMOVED. THIS IS TO PREVENT DAMAGE TO THE POLISHED INNER SURFACE. DO NOT REMOVE THE SUPPORT TUBE FROM THE TWO ENDS OF THE CABLE AT THE SAME TIME.
 (13)
 Move the cable inner member to the fully retracted position at the reverser arm end.

 S 034-034-C00

 (14)
 Remove the nose cap from the conduit cap at the reverser arm end.

 S 844-035-C00

 (15)
 Lubricate the conduit cap threads with grease.

 S 434-036-C00

 (16)
 Carefully put the threaded part of the conduit cap into the slotted retaining bracket.

 NOTE: The washer is installed on the nose cap side of the bracket.
____
 S 434-037-C00
 (17)
 Turn the nose cap on the conduit cap.

 (18)
 Tighten the nose cap by hand.

 S 434-039-C00

 (19)
 Install the two clamps that attach the reverser arm end of the feedback cable as follows:

 S 434-038-C00
 (a)  Install a clamp at the 6:30 o'clock position on the fan frame mid-shroud. 1) Install the clamp on the cable.
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 75-32-05
 ALL  ú ú C02 Page 409 ú Jul 15/90
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
////////////////////////A / /
CFM56 ENGINES
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：737-300 400 500 AMM 飛機維護手冊 空氣 AIR(111)