(a)  Keep the rod end bearing and jamnut for the installation procedure.
 S 034-018-C00
 (17)
 Loosen the nose cap and carefully move the conduit cap free from the MEC slotted bracket.

 S 024-019-C00

 (18)
 Remove the VSV feedback cable as follows:

 CAUTION: WHEN YOU MOVE THE CABLE THROUGH THE 6 O'CLOCK STRUT, MAKE
_______ SURE THAT THE BENDS IN THE CABLE HAVE A RADIUS OF MORE THAN 6 INCHES (152 MM) AT ALL TIMES. IF THE BENDS IN THE CABLE HAVE A RADIUS OF LESS THAN 6 INCHES (152 MM), DAMAGE TO THE CABLE CAN OCCUR.
 (a)  
Pull the cable with your hand up the 6 o'clock strut and through the junction plate. 1) Aid the cable end to prevent damage while you pull the

 cable.

 (b)  
Remove the feedback cable from the engine.

 TASK 75-31-02-404-020-C00
 3.  Install the Variable Stator Vane (VSV) Feedback Cable_____________________________________________________
 A. Consumable Materials
 (1)  
Grease - Graphite (CP2101) (AMM 70-10-01/201)

 (2)  
Methyl Ethyl Keytone (MEK) - (CP1040), locally available

 (3)  
Primer - Red 1200 (AMM 70-10-01/201)

 (4)  
Sealant - DC 93-006-1 (AMM 70-10-01/201)

 B. References
 (1)  
AMM 70-10-01/201, Consumable Materials

 (2)  
AMM 78-31-00/201, Thrust Reverser

 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 75-31-02
 ALL  ú ú C02 Page 405 ú Jul 12/00
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
////////////////////////A / /
CFM56 ENGINES
737-300/400/500/ /MAINTENANCE MANUAL ////////////////////////
C. Access
 (1)  
Location Zones 506 Engine No. 1 - attached to the forward stator case of the HPC at the 1:30 and 7:30 o'clock positions

 606  Engine No. 2 - attached to the forward stator case of the HPC at the 1:30 and 7:30 positions

 (2)  
Access Panels
 5739L/5783L Engine No. 1 - Thrust Reverser Half
 5839R/5838R Engine No. 2 - Thrust Reverser Half

 D. Procedure (Fig. 401)
 S 424-021-C00
 CAUTION: WHEN YOU MOVE THE CABLE THROUGH THE 6 O'CLOCK STRUT, MAKE SURE
_______ THAT THE BENDS IN THE CABLE HAVE A RADIUS OF MORE THAN 6 INCHES (152 MM) AT ALL TIMES. IF THE BENDS IN THE CABLE HAVE A RADIUS OF LESS THAN 6 INCHES (152 MM), DAMAGE TO THE CABLE CAN OCCUR.
 (1)  With the MEC end of the cable retracted, put the cable through the junction plate at the 6 o'clock strut.
 NOTE:  The MEC end of the cable is the longer end if it is measured
____
 from the two bolt flange on the cable.

 S 424-022-C00
 (2)  
Carefully aid the cable down the 6 o'clock strut until the fixed flange is against the junction plate.

 S 434-023-C00

 (3)  
Attach the fixed flange to the junction plate with the two bolts and two nuts.

 (a)  
Lubricate the bolt threads with grease.

 (b)  
Tighten the bolts to 100-110 pound-inches
 (11.3-12.4 Newton meters).

 (4)  
Move the lower end of the cable down the 6 o'clock strut to the MEC.

 S 424-024-C00
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 75-31-02
 ALL  ú ú C01 Page 406 ú Jul 12/00
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
////////////////////////A / /
CFM56 ENGINES
737-300/400/500/ /MAINTENANCE MANUAL ////////////////////////
S 034-025-C00
 CAUTION:_______ THE CABLE INNER PART MUST BE IN THE FULLY RETRACTED POSITION
 WHEN YOU REMOVE THE SUPPORT TUBE AND NOSE CAP.  IF THE CABLE
 INNER PART IS NOT IN THE RETRACTED POSITION, DAMAGE TO THE
 POLISHED INNER PART OF THE CABLE CAN OCCUR.
 DO NOT REMOVE THE SUPPORT TUBE FROM EACH END OF THE CABLE AT
 THE SAME TIME.
 (5)  Remove the nose cap from the conduit cap at the MEC end.
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：737-300 400 500 AMM 飛機維護手冊 空氣 AIR(60)