Control Cable Grommets Installation
Figure 401

EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 20-11-07
 ALL  ú ú 01 Page 402 ú Jun 18/99
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400 MAINTENANCE MANUAL
 S 644-004
 (2)  
Apply BMS 5-126 adhesive to the contact area on the NAS1368 grommet.

 S 424-005

 (3)  
Put the grommet in the bulkhead hole.

 S 824-011

 (4)
Put in the Grommet Installation set tool and turn the grommet.

 NOTE: The grommet can be loose in the bulkhead hole, but you must
____
 cut to remove the grommet.

 S 094-018
 (5)  Remove the grommet installation set.
 F. Install the Grommet with the Control Cable Installed (Fig. 401).
 S 114-017
 WARNING: DO NOT GET SOLVENTS IN YOUR MOUTH, OR YOUR EYES, OR ON YOUR
_______ SKIN. DO NOT BREATHE THE FUMES FROM SOLVENTS. SOLVENTS ARE HAZARDOUS MATERIALS. SOLVENTS MAY BE FLAMMABLE OR HARMFUL TO THE ENVIRONMENT. REFER TO PRODUCT MATERIAL SAFETY DATA SHEETS (MSDS) AND LOCAL REQUIREMENTS FOR PROPER HANDLING PROCEDURES.
 (1)  
Clean the contact area with solvent , Series 98-1
 (AMM 20-30-98 or SOPM 20-30-98) .

 S 424-007

 (2)  
Use these steps to install the NAS1368 grommet:

 (a)  
Put in the grommet in the grommet installation set and flip the grommet.

 (b)  
Remove the grommet from grommet installation set.

 (c)  
Split the NAS1368 grommet with a slant cut.

 (d)  
Place the grommet over the control cable.

 (e)  
Apply BMS 5-126 adhesive on the grommet contact area.

 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 20-11-07
 ALL  ú ú 03 Page 403 ú Jun 18/01
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400 MAINTENANCE MANUAL
 (f)
Insert the grommet into the bulkhead hole.

 (g)
Align the slit part of the grommet at the 12 o'clock position.

 S 424-008
 (3) Use this step to install the BACG20H grommet:
 (a)
Apply BMS 5-55 adhesive on the grommet contact area.

 (b)
Install the grommet into the bulkhead hole.

 (c)
Align the slit part of the grommet at the 12 o'clock position.

 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 20-11-07
 ALL  ú ú 01 Page 404 ú Jun 18/99
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400 MAINTENANCE MANUAL
 PRESSURE-SENSITIVE DECALS - REMOVAL/INSTALLATION
________________________________________________
 1.  General_______
 A.  This procedure contains two tasks. The first task is the removal of pressure-sensitive plastic film decals. The second task is the installation of pressure-sensitive plastic film decals.
 B.  Apply external decal sections in a sequence where the ends make an overlap downstream from the line of flight.
 C.  Apply activator to pressure-sensitive adhesives when you apply decals at ambient temperatures below 60°F.
 D.  Clean plastic film decals with naphtha. Do not use adhesive activator.
 E.  You can remove air bubbles in the eight hours after you apply the decal. Make a small hole in the decal film with a sharp pointed instrument, at the edge of bubble, and push air out through the hole.
 F.  You can also install interior decals with the same procedure you use for pressure-sensitive placards (AMM 20-11-16/401).
 TASK 20-11-08-004-000
 2.  Remove Pressure-Sensitive Decals________________________________
 A.  References
 (1) AMM 51-21-01/701, Interior and Exterior Finishes (Paint Stripping)
 B.  Equipment
 (1) Plastic Scraper or Spatula
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：747-400 AMM 飛機維護手冊 STANDARD PRACTICES - AIRFRAME(56)