~.......................................................................... | TABLE 2 | | NORMAL TUBE CLAMP MAXIMUM SPACING | ............................................................................ | Tubing | | Clamp | Clamp Spacing | | OD | | Spacing - Usual | - Special | | (Inches) | Material | (Inches) | *[1] | ............................................................................ | 1/4 | Steel, Titanium | 16.0 | 12.0 | ............................................................................ | 3/8 | Steel, Titanium | 20.0 | 15.0 | ............................................................................ | 3/8 | Aluminum | 16.5 | 12.0 | ............................................................................ | 1/2 | Steel, Titanium | 23.0 | 17.0 | ............................................................................ | 1/2 | Aluminum | 19.0 | 14.0 | ............................................................................ | 5/8 | Steel, Titanium | 22.0 | 18.5 | ............................................................................ | 5/8 | Aluminum | 22.0 | 16.5 | ............................................................................ | 3/4 | Steel, Titanium | 27.5 | 20.5 | ............................................................................ | 3/4 | Aluminum | 24.0 | 18.0 | ............................................................................ | 1.0 | Steel, Titanium | 30.0 | 22.5 | ............................................................................ | 1.0 | Aluminum | 26.5 | 19.5 | ............................................................................ | 1 1/4 | Steel, Titanium | 31.5 | 23.5 | ............................................................................ | 1 1/4 | Aluminum | 28.5 | 21.0 | 2...............….................…........................…...............1
 *[1] Special: Wing Rear Spar, Engine Strut, Engine Aft Fairing
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 20-11-05
 ALL  ú ú 01 Page 412 ú Feb 15/98
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400
MAINTENANCE MANUAL

BACS13AP

BACS13BD SLEEVE
LUBRICATION POINTS
Flareless Tubing Assembly Lubrication Points
Figure 401

EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 20-11-05
 ALL  ú ú 01 Page 413 ú Feb 15/98
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
E47329
A
747-400
MAINTENANCE MANUAL

1

MAKE SURE THE DECREASE OF ID IS NOT MORE THAN
0.005 INCH AFTER PRESET OR 0.015 INCH AFTER MANY TIGHTENINGS
Maximum Collapse of Preset Flareless Sleeve Figure 402
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 20-11-05
 ALL  ú ú 01 Page 414 ú Feb 15/98
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400
MAINTENANCE MANUAL

TUBING SIZE (INCHES)  NOTE:____ USE CARE WHEN SELECTING CORRECT TORQUE FOR REDUCER FITTINGS INSTALLATION TORQUE. FITTINGS. THE BOSS OR BULKHEAD SIZE DETERMINES INSTALLATION TORQUE ON FLARELESS TUBING FITTINGS (POUND-INCHES, |5%) 3 4 
OD  TUBE DASH NO.  STEEL & TITANIUM TUBES 1  ALUMINUM & ANNEALED CRES TUBES 2 

3/16  -3  100  80 
1/4  -4  140  110 
5/16  -5  190  140 
3/8  -6  270  170 
1/2  -8  500  280 
5/8  -10  700  360 
3/4  -12  900  450 
1  -16  1200  750 
1-1/4  -20  1600  900 
1-1/2  -24  2000  900 
2  -32  2000  ---

TORQUE VALUES APPLICABLE TO THE FOLLOWING TUBE ENDS:
A.  21-6-9 CRES AND ALL OTHER CRES TUBE ENDS WITH BACS13BD OR BACS13BX SWAGED SLEEVES
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：747-400 AMM 飛機維護手冊 STANDARD PRACTICES - AIRFRAME(15)