曝光臺 注意防騙 網曝天貓店富美金盛家居專營店坑蒙拐騙欺詐消費者

 (c) RESET COUNT EXCEEDED - This shows the ADL downloaded the record
 incorrectly after five times.
 (d) CHECK MEDIA - This shows that a portion of data on the media is
 not clear.
 S 712-211
 (3) AIRPLANES WITH FMC SOFTWARE UPDATES 7 AND ON;
 The CDU display will also show the failure indications follows:
 (a) CHECK DBL OR INTERFACE - This shows the most probable cause of
 the failure.
 (b) DB EXCEEDS FMC MEMORY - This shows that the navigation database
 is too large for the FMC data base memory.
 (c) RESET COUNT EXCEEDED - This shows the PDL loaded the navigation
 database incorrectly five times.
 (d) DB-OFP INCOMPATIBLE - The database is not compatible with the
 Op Program.
 (e) CHECK MEDIA - This shows that a portion of data on the disk is
 not clear.
 (f) INCORRECT DISK INSERTED - The inserted disk was not in the
 correct order.
 ú  H.  FMC Software Configuration Check
 ú
 ú  S 712-183
 ú  (1) Make sure the CDU display shows the IDENT 1/x page.
 ú  (a) Make sure that the correct part number for the navigation data
 ú  base shows below NAV DATA on the CDU.

 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. AIRPLANES WITH EFIS ú

 34-62-01

 ú ú 08.1 Page 206 ú Jul 12/02
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A 737-300/400/500MAINTENANCE MANUAL
 ú  (b) Make sure the dates for the navigation data base directly below
 ú  ACTIVE are current.
 ú  (c) Make sure the correct part number for the operational program
 ú  shows beLow OP PROGRAM on the CDU.
 ú
 ú  S 712-264
 ú  (2) AIRPLANES WITH FMC SOFTWARE UPDATES 7.X, 8.X, 10.X AND SUBSEQUENT;
 ú  Push the NEXT PAGE button on the CDU.
 ú  (a) Make sure the correct part number for the performance defaults
 ú  database shows below PERF DEFAULTS on the CDU.
 ú 
        ú
 NOTE: If you did not install a performance defaults database____
 ú  the CDU will show DEFAULTXXX below PERF DEFAULTS.
 ú
 ú  (b) AIRPLANES WITH FMC SOFTWARE UPDATE 10.X AND SUBSEQUENT;
 ú  Make sure the correct part number for the software options
 ú  database shows below SW OPTIONS on the CDU.
 ú 
        ú
 NOTE: If you did not install a software options database____
 ú  the CDU will show DEFAULTXXX below SW OPTIONS.
 ú
 S 712-206
 (3) AIRPLANES WITH FMC SOFTWARE UPDATES 7.1 AND ON;
 On PERF FACTORS 1/1 page, make sure the option code is correct.
 I.  Put The Airplane Back to Its Usual Condition
 S 862-221
 CAUTION: MAKE SURE THE POWER ON LIGHT ON THE PDL IS OFF AND POWER IS_______
 REMOVED FROM THE FMCS BEFORE YOU DISCONNECT THE INTERFACE
 CABLE. IF YOU DO NOT DO THIS DAMAGE TO THE EQUIPMENT MAY
 OCCUR.
 (1) Open these circuit breakers:
 (a) P18 Panel
 1) FMC (or FMCS CMPTR)
 (b) AIRPLANES WITH DUAL FMC;
 P6-1 panel
 1) FMCS CMPTR No. 2
 2) FMCS XFER
 S 092-130
 (2) Remove the interface cable from the FMCS data transfer unit
 receptacle.
 S 862-132
 (3) Close these circuit breakers:
 (a) P18 Panel
 1) FMC (or FMCS CMPTR)

 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. AIRPLANES WITH EFIS ú

 34-62-01
 ú ú 08.1 Page 207 ú Jul 12/02

BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A 
737-300/400/500MAINTENANCE MANUAL
 (b) AIRPLANES WITH DUAL FMC;
 P6-1 panel
 1) FMCS CMPTR No. 2
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：737-300 400 500 AMM 飛機維護手冊 導航 NAVIGATION 5(93)