(g)
The takeoff flap setting may also be entered. The default value of 1 is displayed until changed by the operator. Valid entries are 1, 5 or 15, all other entries are rejected.
(h)
The memo block, at the bottom of this page, displays any preflight items not completed for a normal FMCS preflight. When all preflight activity is complete the word STATUS is replaced with COMPLETE.
Departure Initialization
(a)
The departures pages can be accessed from the TAKEOFF REF page, or by pressing DEP/ARR key on CDU and then line selecting DEP on DEP/ARR INDEX.
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. AIRPLANES WITH DUAL FMC ú
34-62-01
ú CONFIG ú 01 Page 72 ú Nov 12/01
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
737-300/400/500MAINTENANCE MANUAL
(b)
The DEPARTURES pages provide a list of departure procedures related to the selected airport.
(c)
When the page is selected, a complete alphabetic list of SIDS contained in the data base (for the airport indicated in the title) are displayed. The SEL or ACT labels indicate the presence of an existing SID in the corresponding route.
(8)
Verify Initialization
(a)
Press INIT REF key.
(b)
Line select TAKEOFF (3L) on INIT/REF INDEX page.
(c)
Verify PRE-FLT COMPLETE is displayed on TAKEOFF REF page. If the preflight is not complete, PRE FLT STATUS will appear on the CDU screen display. The prompts on the screen will indicate what procedure must be performed to complete the preflight procedure.
(9)
Shut Down
(a)
Position IRS mode selectors to OFF.
(b)
Open all FMCS circuit breakers.
(c)
Remove cooling air.
(d)
If no longer required, remove external electrical power.
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. AIRPLANES WITH DUAL FMC ú
34-62-01
ú CONFIG ú 01 Page 73 ú Nov 15/95
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
737-300/400/500MAINTENANCE MANUAL
FLIGHT MANAGEMENT COMPUTER SYSTEM - TROUBLE SHOOTING
____________________________________________________
1. General_______
A. You use the Flight Management System (FMS) Built-In-Test-Equipment (BITE) to identify Flight Management Computer System (FMCS) failures and malfunctions.
B. You can find the FMS BITE procedure in Chapter 22. FMS BITE includes BITE for these systems:
(1)
FMCS
(2)
Digital Flight Control System (DFCS)
(3)
Autothrottle (A/T)
(4)
Inertial Reference System (IRS)
(5)
Electronic Flight Instrument System (EFIS)
C. FMCS, DFCS, A/T and IRS BITE use the FMCS Control Display Unit (CDU) to control the BITE test procedures.
D. When you make the selection of the FMS system, that system gives the necessary data and intructions to do the tests on the CDU.
E. The CDU shows you when a test is completed satisfactorily, or when there is a failure in the FMCS.
F. AIRPLANES WITH OPTIONAL PORTABLE CDU RECEPTACLE; There is a receptacle in the electrical/electronic equipment (E-E) bay, where you can connect a portable CDU. You use the portable CDU to operate the FMS BITE from the E-E bay.
G. AIRPLANES WITH OPTIONAL PORTABLE PRINTER RECETACLE; There is a receptacle on panel P18, where you can connect a portable printer. You can use the portable printer during FMCS BITE.
H. AIRPLANES WITH FMC SOFTWARE P/N 549297-005 (U7.4) AND ON, OR 549250-004 (U8.4) AND ON, OR 549849-004 (U10.1) AND ON; After an FMC failure occurs, you can get data from the FMC to find the cause of the failure. You use the Portable Data Loader (PDL) or Airborne Data Loader (ADL), as applicable, to make a copy of the data on a 3.5 inch disk.
2. FMCS BITE Trouble Shooting__________________________
A. You can find the procedure for the FMCS BITE trouble shooting in
Section 22-02-00, FMCS BITE - T/S.
NOTE: BITE trouble shooting for other FMS systems are in these 中國航空網(wǎng) m.k6050.com 航空翻譯 www.aviation.cn 本文鏈接地址：737-300 400 500 AMM 飛機維護手冊 導航 NAVIGATION 5(88)
