(c)  
If the FMC detects a failure of any of the Built-In Test (BIT) checks, it will shut itself off from transmitting data to other airplane systems. If it has the capability the FMC will still execute its maintenance BITE processes to assist in further troubleshooting. If the CDU detects any internal failures through execution of its BIT, the CRT screen is immediately blanked.

 (4)  
Airplane Sensors

 (a)  The on-line test on airplane sensors checks that digital data is received at a rate expected for a functioning system. The on-line tests also ensure that digital data as received has correct parity and Sign/Status Matrix (SSM). In addition the tests verify that data received from certain input channels is within reasonable limit values.
 C. Power-Up Tests
 (1)  The power-up tests do not operate as background tasks of the FMCS operational flight program, because the tests would interrupt normal data processing. Due to this, the tests are automatically performed at initial power-up, or after a system power interruption. The power-up tests may also be initiated by pressing the FMC test pushbutton, located on the front panel of the FMC (which is accessible when the airplane is on the ground). The power-up tests detect most internal FMC failures.
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. AIRPLANES WITHOUT EFIS ú

 34-62-00

 ú ú 03 Page 56 ú Feb 25/87
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
737-300/400/500MAINTENANCE MANUAL
 (2)  Upon power-on, the power-up tests cause the FMC fail lamp (located on the front panel of the FMC) to illuminate. The internal ARINC digital input/output channels are then tested, followed by tests on the FMC input/output processor and its memory. The power-up tests then check the performance and navigation processors and their memories. If there are no test failures the FMC fail lamp is extinguished, and the system is initialized for flight operations.
 D. Ground Maintenance Support
 (1)  
General

 (a)  
Built-In-Test-Equipment (BITE) is a function of the FMCS. This function provides ground maintenance personnel with a procedure for troubleshooting the FMS.

 (b)  
A further supplement to ground maintenance is the portable data loader. The protable data loader is used, as required, to load and update the navigation data base of the FMC.

 (2)  
Fault Recording for Maintenance

 (a)  The FMCS aids the operator in isolating faults that occur in sensors and components that interface with the FMCS. A failure noted in the air sometimes cannot be duplicated on the ground. To help in deciding which part of the avionics is responsible for interruption of FMS operation, the FMCS provides a group of maintenance function pages. These pages record the in-flight failure history of interfacing sensors and components. The recording is maintained in the FMC NV RAM; the data is collected and held for failure incidents of the past nine flights. The FMCS records the reason for the failure, the approximate time of the failure, and the unit in which the failure was detected.

 (3)  
Total FMS BITE

 (a)  The CDU acts as the focal control and display for actuating and evaluating FMCS, DFCS, A/T, and IRS self-tests. When the airplane is on the ground, these tests are available for use by maintenance personnel. Once the test has been initiated from the CDU, the system under test will transmit plain text messages, for display on the CDU. In response to the messages the operator can set flight deck controls, and/or perform data entries through the CDU. Test passage or failure is indicated on the CDU display.
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. AIRPLANES WITHOUT EFIS ú

 34-62-00
 ú ú 03 Page 57 ú Feb 25/87

BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
737-300/400/500MAINTENANCE MANUAL
 13. FMCS Messages_____________
 A. General
 (1)  The FMCS (Flight Management Computer System) displays a set of messages for information. These messages are displayed in the scratch pad line of the CDU when conditions warrant their appearance. There are three categories of messages. the messages have a defined priority for display should their set conditions occur at the same time. The three types, listed in order of highest priority, are: Alerting Messages, Entry Error Advisory Messages, and Readiness Advisory Messages
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：737-300 400 500 AMM 飛機維護手冊 導航 NAVIGATION 5(6)