Outward Flare of Lip
Figure 603

EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 34-11-11

 ALL  ú ú 02 Page 604 ú Nov 15/97
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
737-300/400/500MAINTENANCE MANUAL
 S 906-013
 (6)  Replace the pitot-static probe if one of the conditions is not permitted (AMM 34-11-11/401).
 TASK 34-11-11-206-024
 3.  Pitot-Static Probe Inspection (WITH PITOT-STATIC PROBE TIP INSPECTION KIT)_____________________________
 A. Standard Tools and Equipment
 (1)  Pitot-Static Probe Tip Inspection Kit - Model 885N Rosemount Aerospace, Inc. 14300 Judical Road Burnsville, MN 55306-4898 USA Attention: Customer Support Mail Station HE15 Phone: 612-892-4373 Fax: 612-435-3512
REJECTION CRITERION:
1. INDENTATION EXCEEDING 0.030 INCH

Indentation of Pitot Opening
Figure 604

EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 34-11-11

 ALL  ú ú 01 Page 605 ú Mar 15/98
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
E48291
A 737-300/400/500MAINTENANCE MANUAL
 B. References
 (1) 34-11-11/401, Pitot-Static Probe
 C. Access
 (1)  Location Zones
 101/102 Control Cabin
 202 Lower Nose Compartment
 208 Forward Cargo Compartment

 D. General Probe Condition Check
 S 216-025
 (1) Visually examine the pitot static probe for damage.

Chips or Nicks In Probe Tip
Figure 605

EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 34-11-11

 ALL  ú ú 01 Page 606 ú Jul 15/97
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
737-300/400/500MAINTENANCE MANUAL
 S 216-026
 (2)  
Visually examine the pitot static probe for material in the static ports, pitot opening, and pitot drain hole.

 S 906-027

 (3)  
Replace the pitot-static probe if one of the conditions is not satisfactory (AMM 34-11-11/401).

 E. Aerodynamic Contour Condition Check
 S 226-028
 (1)  Visually examine the static ports as follows (Fig. 601):
 (a)  
Make sure that the static port edges are perpendicular to the contoured-surface.

 (b)  
Make sure that the static port edges are not rounded more than

 0.003 inches.

 (c)  
Make sure that the static port edges are not above the contoured-surface more than 0.003 inches.

 S 226-029
 (2)  Visually examine the pitot-static probe for nicks, scratches, or other surface defects as follows:
 (a)  
Make sure that the depth of the defect is less than 0.015 inches within a radius of 0.5 inches of the static ports.

 (b)  
Make sure that the depth of the defect is less than 0.025 inches on the remaining head section.

 (c)  
Make sure that the depth of the defect is less than 0.125 inches on the strut section.

 S 906-030
 (3)  Replace the pitot-static probe if one of the conditions is not permitted (AMM 34-11-11/401).
 F. Pitot Tip Condition Check
 S 226-021
 (1)  
Examine the pitot tip of the probe with the inspection kit.

 S 906-022

 (2)  
Replace the pitot-static probe if the inspection shows an out of tolerance condition (AMM 34-11-11/401).

 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 34-11-11

 ALL  ú ú 02 Page 607 ú Nov 12/99
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：737-300 400 500 AMM 飛機維護手冊 導航 NAVIGATION 1(58)