(2)  
Pitot-static probe adapter kit, P/N AD-953-7, Nav-Aids Ltd., Montreal, Canada; or equivalent

 (3)  
Flow restrictors, control valves, cutoff valves, vinyl adhesive tape, and port seals as required

 B. References
 (1)  
24-22-00/201, Manual Control

 (2)  
34-11-11/601, Pitot-Static Probe

 C. Prepare for the Test
 S 865-126
 (1)  Supply electrical power (Ref 24-22-00/201).
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. AIRPLANES WITHOUT EFIS ú
 34-11-00

 ú ú 08 Page 520 ú Nov 12/99
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
737-300/400/500MAINTENANCE MANUAL
 S 865-127
 WARNING:_______YOU MUST OPEN THE FLAP LOAD RELIEF CIRCUIT BREAKER. YOU CAN CAUSE INJURY TO PERSONS.
 (2)  Open the FLAP LOAD RELIEF circuit breaker on the load control panel P6.
 S 485-129
 WARNING:_______MAKE SURE THAT THE PROBE HEAT IS NOT ON. YOU CAN CAUSE INJURY TO PERSONS.
 (3)  Install the pitot-static probe adapter on the lower left pitot-static probe.
 CAUTION:_______DO NOT EXTEND THE SEALS INTO THE PITOT DRAINS. YOU CAN CAUSE CAMAGE TO THE SURFACE IN THE AREA WHEN YOU REMOVE THE SEALS.
 (a)  Seal the pitot chamber drain hole on the bottom of the probe with vinyl adhesive tape.
 NOTE: You will find the drain hole about 2.25 inches aft of
____
 the probe tip.

 CAUTION: MAKE SURE THAT YOU FLUSH THE PROBE ADAPTER WITH WATER
_______ BEFORE YOU ATTACH THE ADAPTER TO THE PROBE. YOU CAN CAUSE DAMAGE TO THE PROBE OR THE ADAPTER.
 (b)  
Flush the probe adapter with water. NOTE: A solution that has equal parts of ethylene glycol and

____ water must be used in temperatures between 32 degrees F and -40 degrees F.

 (c)  
Install the probe adapter on the probe.

 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. AIRPLANES WITHOUT EFIS ú
 34-11-00
 ú ú 10 Page 521 ú Nov 12/99

BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
737-300/400/500MAINTENANCE MANUAL
 S 485-130
 CAUTION: MAKE SURE THAT THE PITOT-STATIC PROBE HAS NO ADDED WEIGHT FROM
_______ THE TEST HOSES. YOU CAN BEND OR TWIST THE PITOT-STATIC PROBE OUT OF TOLERANCE.
 (4) Connect the pneumatic test set to the pitot-static probe adapter.
 (a)  
Connect the pitot (pressure) source in the pneumatic test unit through the pitot control valve to the pitot cutoff valve.

 (b)  
Connect the inlet of the probe adapter to the pitot cutoff valve through the pitot system test gage and flow restrictor.

 (c)  
Open the pitot cutoff valve.

 D. The Auxiliary No. 2 Pitot System Leak Test
 S 865-316
 CAUTION: MAKE SURE THAT THE PITOT LINE PRESSURE IS EQUIVALENT OR MORE
_______ THAN THE STATIC LINE PRESSURE. KEEP THE PITOT PRESSURE CHANGE BELOW 300 KNOTS FOR EACH MINUTE. MAKE SURE THAT THE DIFFERENTIAL PRESSURE STAYS BETWEEN 0 AND 10.00 INCHES OF MERCURY. YOU CAN CAUSE DAMAGE TO THE PITOT-STATIC SYSTEM.
 (1)  Apply pressure to the auxiliary No. 2 pitot system equal to 300 |5 knots of airspeed (ambient pressure plus 4.53 |0.16 in. Hg).
 S 865-134
 CAUTION: HOLD THE PRESSURE, AS AN ALTERNATIVE, BEHIND THE CUTOFF VALVES
_______ DURING THE CUTOFF TIME. YOU CAN CAUSE DAMAGE TO THE EQUIPMENT WHEN YOU OPEN THE CUTOFF VALVES WITHOUT THE PRESSURE.
 (2)  
Close the pitot cutoff valve to the auxiliary No. 2 pitot system when the necessary airspeed is reached.

 (3)  
Stop for 5 to 6 minutes to allow the system to stabilize.

 S 865-136
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. AIRPLANES WITHOUT EFIS ú
 34-11-00

 ú ú 09 Page 522 ú Nov 12/99
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：737-300 400 500 AMM 飛機維護手冊 導航 NAVIGATION 1(25)