34-22-00
ú ú 05A Page 31 ú Jul 15/95
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A 737-300/400/500MAINTENANCE MANUAL
RISING RUNWAY
RADIO ALTITUDE
DHDH ALERT DH RESET
DH DH ALERT DH RESET RADIO ALTITUDE RISING RUNWAY
SIGNAL TYPES: RAD ALT - DC ANALOG RA VALID - +28V DC: INVALID - OPEN EFIS CP DIGITAL DATA BUS - LO-SPEED ARINC 429
PROGRAM PIN
OPTIONS: 1) RAD ALT SOURCE (ANALOG OR ARINC 700) 2) RA DIAL 3) RISING RUNWAY 4) HEIGHT ALERT
OPTION CAN BE DISABLED BY
PROGRAM PIN CHANGE
EFIS Symbol Generator - Radio Altimeter Inputs Figure 12
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. AIRPLANES WITH EFIS ú
34-22-00
ú ú 05A Page 32 ú Mar 15/91
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A 737-300/400/500MAINTENANCE MANUAL
C. During the airplane descent, when the radio altitude reaches the selected DH value, the DH alert circuity will be set. This causes the DH readout on the EADI to change color and start flashing.
D. The DH alert circuit can be reset, if one of the following conditions are satisfied:
(1)
Radio altitude value equals zero.
(2)
Radio altitude value increases to 75 feet above the DH value.
(3)
By pressing RST (reset) switch on the EFIS control panel.
18. EFIS - FCC/MCP Interface (Fig. 13)
________________________
A. The Flight Control Computers (FCCs) provide inputs to the EFIS symbol generators. Two separate ARINC 429 digital data buses, one from each FCC, are inputs to each symbol generator.
B. Each EFIS symbol generator receives the following data from the onside FCC:
(1)
Selected heading or selected course
(2)
Flight director ON/OFF discrete
(3)
Flight director Pitch/Roll bar drive signals
(4)
Localizer/glide slope deviation warning discretes
C. If the selected heading or selected course data from an FCC becomes invalid, the symbol generator will automatically receive the data from the onside DFCS mode control panel (MCP).
D. If the VHF NAV transfer switch is placed in BOTH ON 1 position, both EFIS symbol generators will use the selected course No. 1 value being received from FCC-A. Similarly, if BOTH ON 2 position is selected, both symbol generators will use the selected course No. 2 value being received from FCC-B.
E. For autopilot operation, the first FCC engaged in the command mode is considered the master, and the remaining FCCs are considered the slave. If the flight director and the autopilot are both off, then FCC-A is considered the master. The MCP will indicate the master FCC by displaying MA.
F. Both EFIS symbol generators use the airspeed bug drive value, as well as the DFCS mode and status data from the master FCC.
19. EFIS - Autothrottle Interface (Fig. 14)
_____________________________
A. The autothrottle computer (A/T) provides inputs to the EFIS symbol generator. The data are transmitted on an ARINC 429 low speed digital data bus. An "A/T installed" discrete signal is also provided to each symbol generator. This is to indicate that an autothrottle computer is installed on the airplane.
B. Each symbol generator transmits the autothrottle mode data for display on the onside EADI. In addition, during the takeoff phase, when the throttle position is stopped, a throttle hold discrete will be received by the symbol generator. This will cause the THR HLD annunciation to appear on the EADIs.
C. The fast/slow command signal is also provided by the autothrottle computer for display on the EADI.
20. EFIS - ADF Interface (Fig. 15)
____________________
A. The Automatic Direction Finder (ADF) provides inputs to the EFIS symbol generators. The signals received by each symbol generator are:
(1)
ADF-1 ON discrete
(2)
ADF-2 ON discrete
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. AIRPLANES WITH EFIS ú
34-22-00
ú ú 09A Page 33 ú Nov 12/00
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A 737-300/400/500MAINTENANCE MANUAL
中國航空網(wǎng) m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：737-300 400 500 AMM 飛機維護手冊 導(dǎo)航 NAVIGATION 1(116)
