C. Find the Applicable Repair Procedure
 S 368-238
 WARNING: MAKE SURE THE FUEL LEAK DOES NOT GO INTO AN IMPORTANT AREA OF
_______ THE AIRPLANE. MAKE SURE THAT LEAKAGE DOES NOT GO INTO THE FUSELAGE AREAS. FUEL LEAKS CAN CAUSE INJURY TO PERSONS AND DAMAGE TO EQUIPMENT.
 (1)  
Refer to AMM 28-11-00/601 to find the applicable repair procedure for the leak type.

 S 398-237

 (2)  
If you find a leak in a fillet seal or a fastener seal, do these steps:

 (a)  Remove the sealant that has the leak.
 NOTE: Refer to the procedure, "Remove the Sealant" in the
____ task, "Repair of Sealant Leaks in the Fuel Tank Structure".
 (b)  
Fully clean the surfaces.

 (c)  
Apply some new sealant to make a seal of the same dimensions as the initial seal.

 NOTE: Refer to the procedure, "Apply the Sealant" in the
____ task, "Repair of Sealant Leaks in the Fuel Tank Structure".
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 28-11-00
 ALL  ú ú 02A Page 802 ú Nov 12/99
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
737-300/400/500MAINTENANCE MANUAL
 S 398-236
 (3)  If you find a leak in a mating surface seal or a prepack seal, do these steps:
 NOTE: Refer to the task, "Repair of Sealant Leaks in the Fuel
____
 Tank Structure".

 (a)  
Disassemble the structure or remove the fasteners.

 (b)  
Repair the structure (Ref SRM, 51-00-00/001).

 (c)  
An alternative procedure is to lift the seal plane (Fig. 812).

 NOTE: Refer to the procedure, "Lift the Seal Plane" in the
____ task, "Repair of Sealant Leaks in the Fuel Tank Structure".
 1) The new seal plane must isolate the seal with the leak from the fuel. 2) You cannot lift the seal plane by a large quantity.
 NOTE: It is usually a better procedure to remove the
____ structure and to replace it.
 S 398-327
 (4)  If you find a leak in an injection seal, do these steps:
 NOTE: You must reject an injection seal if it has air caught in
____ the seal. This causes a space in the seal and can cause a leak.
 (a)  Remove all of the sealant that has the leak.
 NOTE: Refer to the procedure, "Remove the Fuel Tank
____ Sealant" in the task, "Repair of Sealant Leaks in the Fuel Tank Structure".
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 28-11-00
 ALL  ú ú 02A Page 803 ú Nov 12/99
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
737-300/400/500MAINTENANCE MANUAL
 (b)  
Fully clean the channel.

 (c)  
Fill the channels fully with the sealant.

 (d)  
As an alternative procedure, you can lift the seal plane to repair a leak in an injection seal.

 NOTE: Refer to the procedure, "Lift the Seal Plane" in the
____ task, "Repair of Sealant Leaks in the Fuel Tank Structure".
 TASK 28-11-00-208-199
 3. Fuel Leak Analysis to Find the Cause of the Leaks
_________________________________________________
 A. General
 (1)  
These are the causes of most of the leaks in the fuel tank structure:

 (a)  
Surfaces are prepared incorrectly.

 (b)  
Sealants are mixed or kept incorrectly.

 (c)  
Sealants are applied incorrectly.

 (d)  
Fasteners are loose.

 (e)  
The fittings or the connections are installed incorrectly.

 (2)  
This task gives data about the causes of fuel leaks. It also gives general precautions that you must obey when you repair leaks.

 B. Access
 (1)  Location Zones
 221 Center Section Fuel Tank
 305 Left Wing Fuel Tank
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：737-300 400 500 AMM 飛機維護手冊 燃油 FUEL 1(90)