(5)  
C00862 - Alodine 600 powder (SRM 51-20-01)

 (6)  
G01061 - Water, distilled, in 1 gallon containers

 (7)  
One of these sealants:

 (a)  C00307 - BMS 10-20, Type II (preferred) (Ref 20-30-41)
 NOTE: BMS 10-20, Type II mutually compatible with preferred
____
 fuel tank sealant BMS 5-26 Type II.

 CAUTION: USE MIL-C-27725 FINISH MATERIAL ONLY AS A TOPCOAT.
_______
 (b)  C00321 - MIL-C-27725 (Ref 20-30-41) 1) 823-011 or 823-730, DeSoto Chemical Coatings, Inc. 2) PR-1560M, PR-1560MC, PR-1560MK, Products Research Co.
 (8)  
C00922 - Primer - Zinc-rich epoxy

 (a)  
base, 463-6-28, Bostik

 (b)  
catalyst, X-344, Bostik

 (c)
thinner, TL-52, BostikReferences

 (1)  
AMM 12-11-00/301, Fuel Servicing

 (2)  
AMM 20-40-11/201, Static Grounding

 (3)  
AMM 28-10-00/201, Storage

 (4)  
AMM 28-11-00/601, Integral Fuel Tanks

 (5)  
AMM 28-11-00/801, Integral Fuel Tanks

 (6)  
AMM 28-11-11/401, Wing Fuel Tank Access Panels

 (7)  
AMM 28-11-31/401, Center Tank Access Panel

 (8)  
SRM 51-20-01, Protective Treatment of Metallic and Graphite

 MaterialsAccess

 (1)  
Location Zones 221 Center Section Fuel Tank 305 Left Wing Fuel Tank 405 Right Wing Fuel Tank

 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù.
 ú

 28-11-00
 ú ALL ú ú ú 01A.101 Page 716 ú ú Jul 12/02
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
737-300/400/500MAINTENANCE MANUAL
 F. Prepare to Apply the Corrosion Resistant Finish (Topcoat)
 S 687-059
 WARNING: CAREFULLY DO ALL OF THE SAFETY PROCEDURES IN THE FUEL TANK
_______ PURGING AND ENTRY PROCEDURE. INJURIES TO PERSONS AND DAMAGE TO EQUIPMENT CAN EASILY OCCUR.
 (1)  Do the procedure: "Purging (Air Ventilating)" for the applicable tank (Ref 28-10-00/201).
 S 497-060
 WARNING: SUPPLY AN ELECTRICAL GROUND FOR THE ELECTRICAL EQUIPMENT IN THE
_______ OPEN TANK OR NEAR IT. A FIRE OR AN EXPLOSION CAN EASILY OCCUR.
 (2)  Install the air blower and the flexible hose to give a good flow of air to the area in the tank where you do the maintenance.
 (a)  
Use the exhaust fan and the hoses to move the exhaust air from the tank to the empty space away from the work area.

 (b)  
Connect the hoses and the nozzles to an electrical ground (AMM 20-40-11/201).

 S 217-061
 (3)  After you go into the tank, examine these surfaces for fungus or corrosion:
 NOTE: Look for a material of a different color, which is
____ usually a brown color or a black color. When the tanks are wet, the fungus is a black, smooth, moist material. When the tanks are dry, the fungus is a solid material on the tank surfaces. It can have a light brown color.
 (a)  
The bottom of the tank

 (b)  
The top surfaces of the tubing

 S 147-062
 (4)  If you find some loose corrosion finish, do these steps to remove it:
 (a)  
Remove all the loose finish with a wood or plastic scraper.

 (b)  
Clean the structure with a stainless steel brush that turns or with a wire brush that you hold in your hand.

 (c)  
Use pressure sensitive tape to do a check for loose finish of the surfaces adjacent to the areas with loose finish. 1) Apply a strip of the pressure sensitive tape to do a test

 of the surface.
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 28-11-00
 ú  ALL  ú
 ú ú  ú 01A.101 ú BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.  Page 717Jul 12/02 

A
737-300/400/500MAINTENANCE MANUAL
 2) Push the tape down tightly with an even and constant
 pressure. 3) Push down tightly on the full strip of tape. 4) Remove the tape from the surface in one quick movement away
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：737-300 400 500 AMM 飛機維護手冊 燃油 FUEL 1(82)