CAUTION: ALWAYS KEEP THE TEMPORARY REPAIR TOOL PERPENDICULAR TO THE
_______ WING SURFACE. IF YOU DO NOT KEEP THE TEMPORARY REPAIR TOOL PERPENDICULAR TO THE WING SURFACE, DAMAGE TO THE WING SURFACE COULD OCCUR.
 (d)  Operate the rivet gun until sealant is applied around the bad rivet.
 S 218-308
 (5)  
Examine the repair for fuel leaks.

 S 378-309

 (6)  
If the fuel leak continues, do the procedure again.

 S 378-310

 (7)  
If you must replace the self-sealing rivet, refer to the Structural Repair Manual (SRM 51-40-00).

 S 118-311

 (8)  
Clean the sealant from the temporary repair tool and the wing surface with solvent, Series 93 (AMM 20-30-93/201).

 NOTE: Make sure you do not touch the area with the new sealant.
____
 I.  Install a Click Patch
 S 378-312
 (1)  You can use a Click Patch kit to repair fuel leaks through Class C (Heavy Seep) (AMM 28-11-00/601).
 (a)  Click Patch kits contain these items:
 1)  Flat disks (for fasteners that do not come out of the surface)
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 28-11-00
 ALL  ú ú 02A Page 849 ú Nov 12/99
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A 737-300/400/500MAINTENANCE MANUAL
 2) Hatted disks (for rivets or bolts that are above the wing surface). 3) An illustrated sheet that shows the procedure to install the disks.
 S 378-313
 (2)  
Obey the procedures on the sheet to put the disk on the bad fastener.

 S 378-314

 (3)  
These limits apply to Click Patch repairs:

 (a)  
You can install a Click Patch only after you make sure there are no structural cracks in the area of the fuel leak.

 (b)  
A Click Patch has a maximum diameter of 1.25 inches.

 (c)  
A Click Patch is a temporary repair and you must make a permanent repair when it is possible.

 TASK 28-11-00-378-315
 10. Repair of O-Rings and Rubber Seals__________________________________
 A. General
 (1)  
Leaks can occur around plumbing fittings that you can remove, primary tension bolts, tank access doors and fuel system components that go through the fuel tank surfaces. These components are sealed by O-rings or by rubber seals. Replace the O-rings or rubber seals when they are damaged or have fuel leaks. You must apply the alodine layer to all surfaces of the tank structure that are damaged before you install new O-rings or rubber seals.

 (2)  
O-rings are used to seal these types of components:

 (a)  
Plumbing fittings that you can remove

 (b)  
Primary tension bolts

 (c)  
Access doors for the fuel tanks

 (d)  
Fuel system components that go through tank walls.

 (3)  
O-rings are used to seal these components:

 (a)  
Removable plumbing fittings

 (b)  
Primary tension bolts

 (c)  
Access doors for the fuel tank

 (d)  
Fuel system components that go through fuel tank walls.

 (4)  
If an O-ring seal has a leak, you must replace it.

 (5)  
The cast aluminum access doors and the high impact-resistant access doors are sealed with a rubber seal ring. If the seal on a cast aluminum door has a leak, you must replace the door. If a seal on a high impact-resistant door has a leak (the seal becomes loose but has no damage), you can replace the seal. Refer to this task: "Replacement of the Molded Rubber Door Seal" (AMM 28-11-11/801).

 B. Consumable Materials
 (1)  G00267 Gauze pads - unsterilized
 NOTE: All material must contain less than 0.75 percent oil by
____
 carbon tetrachloride extraction.

 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 28-11-00
 ALL  ú ú 02A Page 850 ú Nov 12/99
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：737-300 400 500 AMM 飛機維護手冊 燃油 FUEL 1(108)