28-11-00
ALL ú ú 01 Page 618 ú Mar 12/02
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A 737-300/400/500MAINTENANCE MANUAL
(d) Connect the air hose to the air valve on the tank test door.
CAUTION: FULLY DRAIN THE MANOMETER IMMEDIATELY AFTER YOU DO THE
_______ PRESSURE CHECK IN COLD WEATHER. MAKE CORRECTION TO WATER COLUMN HEIGHT WHEN YOU USE ANTIFREEZE SOLUTION. FREEZING OR INCORRECT PRESSURE CAN CAUSE DAMAGE TO EQUIPMENT.
(e) Fill the manometer with water to the fill mark on the manometer for the applicable pressure or vacuum (Fig. 615).
NOTE: Colored water or a small floating ball makes it
____ easier to monitor the water level in the manometer. Use antifreeze solution in the manometer when the weather is cold.
(f) Open the air valve in the pressure source to apply the pressure.
S 796-079
WARNING: DO NOT PRESSURIZE THE TANK TO MORE THAN THE MAXIMUM SAFE
_______ PRESSURE OF 5.20 PSIG (35.8 KPA GAGE). INJURY TO PERSONS AND DAMAGE TO EQUIPMENT CAN OCCUR.
(3) Pressurize the tank to a maximum of 5.0 psig.
NOTE: The use of negative (vacuum) pressure is not recommended for this
____ test because it can cause more damage to sealant. But, if negative pressure is used, do not apply more negative pressure than -2 psig.
S 796-080
(4) Apply soap solution to the external surface of the wing to find the external leak point.
(a) Monitor the leak area for indications of bubbles.
NOTE: The bubbles show the location of the external leak
____ point. If the leak is small, it can be necessary to monitor the leak area constantly for a long time.
S 796-081
(5)
Make a mark at the location of the bubbles.
S 166-082
(6)
Remove the bubble solution from the external surface of the tank with a moist cloth.
(7)
Remove the pressure from the tank.
S 866-083
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
28-11-00
ALL ú ú 02 Page 619 ú Mar 12/02
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
737-300/400/500MAINTENANCE MANUAL
S 796-084
(8) Find the internal leak source with one of the applicable procedures.
NOTE: For example, do the Air Pressure and Bubble Procedure.
____
I. Hollow Bolt Procedure to Use in Areas With Complex Structure
S 796-085
(1) Do the hollow bolt and air bubble procedure (Try this procedure before you use the hollow bolt and dye injection procedure).
WARNING: CAREFULLY DO ALL OF THE SAFETY PROCEDURES IN THE PURGING
_______ AND ENTRY PROCEDURE FOR THE FUEL TANK. INJURY TO PERSONS AND DAMAGE TO EQUIPMENT CAN OCCUR.
(a)
Do the procedure: Fuel Tank Purging and Entry (AMM 28-10-00/201), for the applicable tank.
(b)
Remove a good fastener and install the hollow bolt fastener in the fastener hole (Fig. 616). 1) Refer to the Structural Repair Manual for the correct
removal and installation procedure.
CAUTION: MAKE SURE THE FUEL TANK VENTS ARE OPEN AND NOT BLOCKED.
_______ IF THE FUEL TANK IS CLOSED (ACCESS DOORS INSTALLED AND VENTS BLOCKED), THE FUEL TANK PRESSURE CAN INCREASE AND CAUSE DAMAGE TO EQUIPMENT.
(c)
Close the clamp on the air bleed hose.
(d)
With the air bleed hose clamp closed, connect the regulated air pressure supply.
(e)
Connect the regulated air pressure supply.
NOTE: The air supply must come through a F71329 leak
____ tracing device. Or there must be a safety relief manometer in the system.
(f) Apply the soap solution to area in the tank where you think the leak is.
CAUTION: MONITOR THE EQUIPMENT CONTINUOUSLY TO MAKE SURE THE
_______ PRESSURE DOES NOT BECOME MORE THAN THE MAXIMUM OF 4 PSI. DAMAGE TO THE FUEL TANK CAN OCCUR.
(g) Supply air pressure with an air source, to the tracer, F71329 and look for air bubbles in the fuel tank.
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：737-300 400 500 AMM 飛機維護手冊 燃油 FUEL 1(52)
