(b)  
Install a jumper between pins 2 and 3 on the pressure switch connector. 1) If the DISC light on the CARGO FIRE panel comes on, then do

 these steps:
 a) Remove the jumper.
 b) Replace fire bottle 1. These are the tasks:

 Cargo Fire Extinguisher Bottle Removal
 (AMM 26-23-01/401)
 Cargo Fire Extinguisher Bottle Installation
 (AMM 26-23-01/401)

 c)  If the installation test for the fire bottle is satisfactory, then you corrected the fault. 2) If the DISC light on the CARGO FIRE panel does not come on, then continue.
 (c)  
Remove connector D12816 from the pressure switch on bottle 2.

 (d)  
Install a jumper between pins 2 and 3 on the pressure switch connector. 1) If the DISC light on the CARGO FIRE panel comes on, then do

 these steps:
 a) Remove the jumper.
 b) Replace fire bottle 2. These are the tasks:

 Cargo Fire Extinguisher Bottle Removal
 (AMM 26-23-01/401)
 Cargo Fire Extinguisher Bottle Installation
 (AMM 26-23-01/401)

 c)  If the installation test for the fire bottle is satisfactory, then you corrected the fault. 2) If the DISC light on the CARGO FIRE panel does not come on, then remove the jumpers and continue.
 (3)  Do a check of the wiring from the pressure switch to the CARGO FIRE panel.
 (a)  Repair the wiring.
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 26-23-00
 ALL  ú ú 01 Page 106 ú Nov 12/00
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
737-300/400/500MAINTENANCE MANUAL
 (b)  Install a jumper between pins 1 and 2 of the pressure switch connector. 1) If the DISCH light on the CARGO FIRE panel comes on, then
 you corrected the fault. Re-connect the connector to the pressure switch.
 (4)  Replace the CARGO FIRE panel, P8-75. To install it, these are the tasks: Cargo Fire Control Panel Removal (AMM 26-00-02/401) Cargo Fire Control Panel Installation ((AMM 26-00-02/401)
 (a)  If the installation test for the CARGO FIRE panel is satisfactory, then you corrected the fault.
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 26-23-00
 ALL  ú ú 01 Page 107 ú Nov 12/00
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
737-300/400/500MAINTENANCE MANUAL
 CARGO BAY EXTINGUISHING - FAULT ISOLATION
_________________________________________
 1.  General_______
 A.  This section contains the Fault Isolation procedures for the cargo bay fire extinguishing system. These include tasks for the squib test light, the discharge light, and for when the bottle does not discharge after the DISCH switch was pushed.
 TASK 26-23-00-812-020
 2.  Squib Test Light Fault Isolation________________________________
 A.  General
 (1)  
This task is for the EXT FWD and AFT lights on the CARGO FIRE panel.

 (2)  
The EXT FWD and AFT lights come on when the TEST switch pushed, to show there is continuity through the squibs. If the lights do not come on, then there is a problem with the discharge system.

 (3)  
These are the possible causes

 (a)  
Squib
 1) M2249 (bottle 1 forward)
 2) M2250 (bottle 1 aft)
 3) AIRPLANES WITH ETOPS;

 M2264 (bottle 2 forward) 4) AIRPLANES WITH ETOPS; M2265 (bottle 2 aft)

 (b)  
CARGO FIRE panel P8-75

 (c)  
Wiring

 (4)  
This is the primary circuit breaker related to the fault:

 (a)  Circuit Breaker Panel, P18-2:
 1) CARGO FIRE EXT 1

 2)  AIRPLANES WITH ETOPS;
 CARGO FIRE EXT 2

 B.  References
 (1)  
SSM 26-23-11

 (2)  
WDM 26-21-11

 C.  Initial Evaluation
 S 812-004
 (1)  Set the DIM/BRT/TEST switch on the captain's instrument panel, P1 to TEST.
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：737-300 400 500 AMM 飛機維護手冊 防火 FIRE PROTECTION(129)