S 864-014

 (3)  
Connect the safety discharge tubing to the thermal relief discharge port.

 S 864-013
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 26-22-11
 ALL  ú ú 03 Page 404 ú Nov 12/01
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
737-300/400/500MAINTENANCE MANUAL
 S 864-015
 (4)  If the bottle does not have a squib installed, install the discharge squib in fire extinguisher discharge plug. Tighten the squib to 96 |12 pound-inches and attach a lockwire.
 NOTE:____The squib must be examined for damage. Make a check of the
 soft seal opposite the electrical connector, which protects the explosive charge. Replace the squib if it is damaged or has a hole.
 S 864-016
 CAUTION: IF A SHUNT PLUG IS INSTALLED, PULL THE SHUNT PLUG STRAIGHT OFF
_______ THE FIRE BOTTLE SQUIB. IF YOU TWIST OR WIGGLE THE SHUNT PLUG, YOU CAN CAUSE DAMAGE TO THE SQUIB PINS.
 (5)  
If a protective cover is installed on the squib, remove the protective cover.

 S 024-031

 (6)  
If a shunt plug is installed, pull the shunt plug straight off the squib and discard the shunt plug.

 NOTE: Shunt plugs should not be used to cover the fire bottle
____ squibs because they can cause damage to the squib pins.
 S 864-027
 WARNING:_______MAKE SURE THERE IS NO VOLTAGE AT THE ELECTRICAL CONNECTOR. IF THERE IS A VOLTAGE AT THE ELECTRICAL CONNECTOR, THE SQUIB CAN RELEASE ITS CONTENTS SUDDENLY AND CAUSE INJURY TO PERSONS.
 (7)  Make sure there is no voltage between pins 1 and 2 of the electrical connector.
 NOTE: If you use a voltmeter, connect a 10 Kohm resistor across
____
 the meter. You should read less than 1 volt.

 S 864-019
 (8)  Make sure the electrical connector is not damaged.
 NOTE: The squib pins can cause damage to the electrical connector
____
 if the pins do not enter the connector receptacles.

 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 26-22-11
 ALL  ú ú 01 Page 405 ú Nov 12/01
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
737-300/400/500MAINTENANCE MANUAL
 S 864-020
 (9)  
Connect the electrical connectors to the discharge squib and the pressure switch.

 S 864-021

 (10)
 Do an operational test as described in AMM 26-22-00/501.

 S 864-022

 (11)
 Close the 3701 access door.

 S 864-023

 (12)
 Close the APU extinguisher bottle and all IND LIGHTS circuit breakers on the load control center P6.

 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 26-22-11
 ALL  ú ú 03 Page 406 ú Nov 12/99
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
737-300/400/500MAINTENANCE MANUAL
 APU FIRE EXTINGUISHER BOTTLE - INSPECTION/CHECK
_______________________________________________
 1.  General
 A.  This subject has two tasks. The first task is a check of the bottle pressure.
 B.  The second task is a check of the service life of the squib cartridge.
 TASK 26-22-11-756-001
 2.  Inspection/Check - Fire Extinguisher Bottle -------------------------------------------
A.  Procedure
 S 756-002
 (1)  Make a Check of the Bottle Pressure.
 (a)  Remove and weigh the bottle to find its condition. The total weight marked on the nameplate includes: the discharge outlet, the squib with protective cap, the fill fitting, and the extinguishing agent. The maximum weight of a serviceable fire extinguisher bottle with the squib installed is identified on the nameplate. You must replace the bottle if the bottle weight is 0.10 pounds less than the total weight identified on the nameplate.
 TASK 26-22-11-756-005
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：737-300 400 500 AMM 飛機維護手冊 防火 FIRE PROTECTION(120)