TASK 26-22-21-202-002
3. Check the Squib_______________
A. Do these steps to check the squib.
S 862-029
WARNING: DO NOT TOUCH THE SQUIB BEFORE YOU DO THE PROCEDURES FOR DEVICES
_______ THAT ARE SENSITIVE TO ELECTROSTATIC DISCHARGE. ELECTROSTATIC DISCHARGE CAN CAUSE THE FIRE BOTTLE TO RELEASE ITS CONTENTS SUDDENLY AND CAUSE INJURY TO PERSONS AND DAMAGE TO EQUIPMENT.
(1) Before you touch the squib, do the procedure for devices that are sensitive to electrostatic discharge (AMM 20-40-12/201).
(a) If the squib has corrosion on its threads, replace it with a new squib.
TASK 26-22-21-402-003
4. Install the Squib
_________________
A. Do these steps to install the squib.
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
26-22-21
ALL ú ú 01 Page 202 ú Nov 12/01
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A 737-300/400/500MAINTENANCE MANUAL
S 862-030
WARNING:_______ DO NOT TOUCH THE SQUIB BEFORE YOU DO THE PROCEDURES FOR DEVICES
THAT ARE SENSITIVE TO ELECTROSTATIC DISCHARGE. ELECTROSTATIC
DISCHARGE CAN CAUSE THE FIRE BOTTLE TO RELEASE ITS CONTENTS
SUDDENLY AND CAUSE INJURY TO PERSONS AND DAMAGE TO EQUIPMENT.
(1)
Before you touch the squib, do the procedure for devices that are sensitive to electrostatic discharge (AMM 20-40-12/201).
S 032-009
(2)
Remove the caps and install the squib in the bottle fitting. S 432-010
(3)
Tighten the squib to 96 |12 pound-inches. S 432-011
(4)
Install new lockwire.
S 032-020 CAUTION: IF A SHUNT PLUG IS INSTALLED, PULL THE SHUNT PLUG STRAIGHT OFF
_______ THE FIRE BOTTLE SQUIB. IF YOU TWIST OR WIGGLE THE SHUNT PLUG, YOU CAN CAUSE DAMAGE TO THE SQUIB PINS.
(5)
If a protective cover is installed on the squib, remove the protective cover.
S 022-026
(6)
If a shunt plug is installed, pull the shunt plug straight off the squib and discard the shunt plug.
NOTE: Shunt plugs should not be used to cover the fire bottle
____ squibs because they can cause damage to the squib pins.
S 762-024
WARNING:_______MAKE SURE THERE IS NO VOLTAGE AT THE ELECTRICAL CONNECTOR. IF THERE IS A VOLTAGE AT THE ELECTRICAL CONNECTOR, THE SQUIB CAN RELEASE ITS CONTENTS SUDDENLY AND CAUSE INJURY TO PERSONS.
(7) Make sure there is no voltage between pins 1 and 2 of the electrical connector.
NOTE: If you use a voltmeter, connect a 10K ohm resistor across
____ the meter. You should read less than 1 volt.
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
26-22-21
ALL ú ú 01 Page 203 ú Nov 12/01
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
737-300/400/500MAINTENANCE MANUAL
S 212-023
(8) Make sure the squib electrical pins are not bent or damaged.
(a) Make sure the electrical connector is not damaged.
NOTE: The squib pins can cause damage to the electrical
____ connector if the pins do not enter the connector receptacles.
S 032-012
(9)
Connect the electrical connector to the fire bottle squib.
S 032-013
(10)
Do the APU fire extinguishing A/T (AMM 26-22-00/501).
S 412-014
(11)
Close the access door, 3701.
S 862-016
(12)
Close these circuit breakers and remove the DO-NOT-CLOSE tags:
(a) P6 Load Control Center Panel
1) EXT BOTTLE APU
2) IND LIGHTS (all)
S 862-015
(13) Remove the electrical power if it is no longer required (AMM 24-22-00/201).
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
26-22-21
ALL ú ú 01 Page 204 ú Nov 15/96
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：737-300 400 500 AMM 飛機維護手冊 防火 FIRE PROTECTION(122)
