曝光臺 注意防騙 網曝天貓店富美金盛家居專營店坑蒙拐騙欺詐消費者

 WARNING: MAKE SURE THAT PERSONS AND EQUIPMENT ARE CLEAR OF ALL
_______ CONTROL SURFACES BEFORE YOU SUPPLY HYDRAULIC POWER. AILERONS, RUDDERS, ELEVATORS, FLAPS, SPOILERS, LANDING GEAR, AND THRUST REVERSERS CAN MOVE QUICKLY WHEN YOU SUPPLY HYDRAULIC POWER. THIS CAN CAUSE INJURY TO PERSONS OR DAMAGE TO EQUIPMENT.
 (2)  Supply hydraulic power (Ref 27-11-00/201).
 D. Actuator/Sensor Test
 S 865-070
 (1)
Put the autopilot A (or B as applicable) engage switch to CWS.

 S 755-016

 (2)  
Make sure CWS roll and CWS pitch lights come on.

 (3)  
Turn the control wheel left and make sure the left aileron moves up.

 S 825-017

 (4)  
Turn the control wheel right and make sure the right aileron moves up.

 S 865-072

 (5)  
Put the control wheel to center detent and make sure the ailerons are in the center.

 S 865-071
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 22-11-29
 ALL  ú ú 02 Page 508 ú Jul 12/01
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A 737-300/400/500MAINTENANCE MANUAL
 (6)  S 865-073Disengage the autopilot.
 (7)  S 865-074Remove electrical power if it is not necessary.
 (8)  S 865-075Remove hydraulic power if it is not necessary.

 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 22-11-29
 ALL  ú ú 01 Page 509 ú Jul 15/91
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
737-300/400/500MAINTENANCE MANUAL
 ELEVATOR POSITION SENSOR - REMOVAL/INSTALLATION
_______________________________________________
 1.  General (Fig. 401)_______
 A.  This procedure contains two tasks. The first is for the removal of the elevator position sensor. The second is for the installation of the elevator position sensor.
 B.  The elevator position sensor is connected to the elevator torque tube and is installed on the aft bulkhead station 1156 (Ref 27-31-00/201 Elevator and Tab Control System). The elevator position sensor is connected to the lower (input) torque tube (adjacent to lower RH control cable quadrant).
 TASK 22-11-30-024-001
 2.  Elevator Position Sensor Removal________________________________
 A.  References
 (1)  
12-31-41/201, Access Doors and Panels

 (2)  
27-31-00/201, Elevator and Tab Control System

 B.  Access
 (1)  
Location Zone
 705 Tail Cone Access Door

 (2)  
Access Panel
 3802 Tail Cone Access Door

 

 C.  Prepare for Removal
 S 014-002
 (1)  
Remove access panel 3802 on the tail cone (Ref 12-31-41/201, Access Doors and Panels).

 S 864-003

 (2)  
Open these circuit breakers and attach DO-NOT-CLOSE tags:

 (a)  
P6 Circuit Breaker Panel
 1) AUTO FLT CONT SYS B MACH TRIM AC
 2) AUTO FLT CONT SYS B SNSR EXC AC

 (b)  
P18 Circuit Breaker panel
 1) AUTO FLT CONT SYS A MACH TRIM AC
 2) AUTO FLT CONT SYS A SNSR EXC AC
 3) AUTO FLT CNT AUTOTHROTTLE AC
 4) AUTO FLT CNT YAW DAMPER AC

 

 

 D.  Elevator Position Sensor Removal
 S 034-005
 (1)  
Disconnect the electrical connectors on the sensor.

 S 034-004

 (2)  
Remove the bolt and lock nut from the crank clamp attached to the micro adjustment rod assembly.

 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 22-11-30
 ALL  ú ú 02 Page 401 ú Jul 15/98
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A 737-300/400/500MAINTENANCE MANUAL
SEE  A 
SHAFT INPUT QUADRANT  ELEVATOR B PCU 
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：737-300 400 500 AMM 飛機維護手冊 自動飛行 AUTOFLIGHT 2(23)