(2)
Access
1201 Electronic Equipment Access Door
B. Procedure
S 024-001
(1) Remove the actuator assembly:
(a)
Set the thrust lever in the idle position.
(b)
Open the autothrottle system AC and DC circuit breakers on P18 panel.
(c)
Release the four bolts (two on each side of the actuator assembly).
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
22-31-91
ALL ú ú 02 Page 401 ú Mar 15/99
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A 737-300/400/500MAINTENANCE MANUAL
LEFT AND RIGHT AUTOTHROTTLE SERVOMECHANISMS (STA 370)
SEE A
POTENTIOMETER ASSEMBLY (IF INSTALLED)
ACTUATOR ASSEMBLY
STA 360
TORQUE SWITCH
FWD TORQUE SWITCH MECHANISM
CONNECTOR ACTUATOR ASSEMBLY
A SEE B
ATTACHMENT BOLTS
B
(4 LOCATIONS)
Autothrottle Servomechanism Components InstallationFigure 401
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
22-31-91
ALL ú ú 01 Page 402 ú Nov 15/94
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A 737-300/400/500MAINTENANCE MANUAL
(d)
Remove the actuator assembly from the torque switch mechanism carefully.
(e)
Disconnect the electrical cable from the actuator assembly.
S 024-002
(2) Remove the Torque Switch:
NOTE: You can remove the torque switch and ignore the rigging
____ installation of the throttle cable.
(a)
Disconnect the torque switch pigtail from the adjacent terminal block.
(b)
Remove the two screws which attach the torque switch to the top of the torque switch mechanism assembly.
(c)
Remove the torque switch from the torque switch mechanism assembly.
TASK 22-31-91-404-009
3. Autothrottle Servomechanism Components Installation
___________________________________________________
A. Consumable Materials
(1) MIL-G-81322, Grease (70-10-01/201)
B. References
(1)
AMM 24-22-00/201, Manual Control
(2)
AMM 22-31-00/501, Autothrottle System - Adjustment/Test
C. Access
(1)
Location Zone
205 Electronic Compartment
(2)
Access
1201 Electronic Equipment Access Door
D. Procedure
NOTE: Make sure the shaft and the gears are in good condition.
____ S 424-005
(1) Install the actuator assembly:
(a)
Apply a thin layer of grease to the pinion of the actuator assembly.
(b)
Turn the actuator assembly so that the electrical connector is toward the aft end of the airplane.
(c)
Connect the electrical cable to the actuator assembly.
(d)
Set the actuator assembly in the location against the torque switch mechanism.
(e)
Tighten the four bolts (two on each side of the actuator assembly).
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
22-31-91
ALL ú ú 03 Page 403 ú Mar 15/99
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
737-300/400/500MAINTENANCE MANUAL
S 424-007
(2) Install the Torque Switch:
(a)
Set the torque switch on top of the torque switch mechanism assembly.
(b)
Tighten the torque switch with a short slot screwdriver.
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：737-300 400 500 AMM 飛機維護手冊 自動飛行 AUTOFLIGHT 2(175)
