(c)  
Push the LSK adjacent to (MAINT>) and make sure that the CDU shows MAINT BITE INDEX.

 (d)  
Push the LSK adjacent to (<DFCS) and make sure that the CDU shows DFCS BITE TEST 1/2.

 (e)  
Push the NEXT PAGE key and make sure that the CDU shows DFCS BITE TEST 2/2.

 (f)  
Push the LSK adjacent to (<RIGGING) and make sure that the CDU shows BITE TEST ELEV RIG 50.00.

 (g)  
Remove hydraulic power as shown on the CDU display.

 WARNING: MAKE SURE PERSONS AND EQUIPMENT ARE CLEAR OF THE CONTROL
_______ COLUMN WHILE THE TEST CONTINUES. THE CONTROL COLUMN CAN MOVE WHICH CAN CAUSE INJURY TO PERSONS AND DAMAGE TO EQUIPMENT.
 (h)  
Push the LSK adjacent to (<AILERON) and make sure that the CDU shows DFCS BITE TEST AILERON RIG 52.00.

 (i)  
Do these instructions on the CDU: 1) Make sure all control surfaces are clear 2) Supply hydraulic power to systems A and B 3) Set the aileron trim to 0 degrees. 4) Set the flaps to 1 unit 5) Put the A/P A engage switch in the CMD position

 NOTE: If there is no response, push the LSK adjacent to
____ (<PUSH IF NO RESPONSE) to go back to the rigging menu.
 6) Put the A/P B engage switch to the CMD position
 NOTE: If there is no response, push the LSK adjacent to
____ (<PUSH IF NO RESPONSE) to go back to the rigging menu.
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 22-11-29
 ALL  ú ú 01 Page 506 ú Jul 15/97
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
737-300/400/500MAINTENANCE MANUAL
 7)  Push the LSK adjacent to (<CONTINUE) to show AILERON RIG page 52.02.
 NOTE: Use this display to make sure the ailerons are at
____
 null.

 S 825-014
 (2)  Adjust the aileron position sensor
 (a)  
Loosen the screw on the sensor clamp until you can turn the sensor.

 (b)  
Turn the sensor housing slowly until you get a value less than 60mV.

 (c)  
Tighten the clamp screw to 8 to 12 pound-inches.

 (d)  
Remove the lockwire and turn the thumbnut on the microadjustment rod until you get the smallest value less than 60mV.

 (e)  
Install the lockwire on the thumbnut.

 (f)  
Do the test again for the B system and make sure the B system sensors are nulled.

 S 865-015
 (3)  Push the INIT REF key on the CDU to get out of BITE.
 TASK 22-11-29-745-057
 4.  Aileron Position Sensor Test (BITE TEST)
____________________________
 A.  Access
 (1)  Location Zone
 102 Control Cabin

 B.  DFCS BITE test.
 S 865-060
 (1)  
Push the LSK adjacent to (<LRU INTERFACE).

 (2)  
Push the LSK adjacent to (<CHANNEL A and B).

 (3)  
Push the LSK adjacent to (<LRU INTERFACE TESTS 2/2).

 (4)  
Push the CDU NEXT PAGE key.

 (5)  
Push the LSK adjacent to (<ACT POS SENS).

 S 865-058
 S 865-059
 S 865-061
 S 865-062
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 22-11-29
 ALL  ú ú 01 Page 507 ú Nov 15/91
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A 737-300/400/500MAINTENANCE MANUAL
 S 865-063
 (6)  Make sure that BITE completes the sensor tests and that AIL POS tests are done without an indication of failure.
 TASK 22-11-29-715-064
 5.  Aileron Actuator/Position Sensor - Manual Test________________________________
 A. References
 (1)  
12-31-41/201, Access Doors and Panels

 (2)  
24-22-00/201, Electrical Power Control

 (3)  
27-11-00/201, Aileron and Aileron Trim Control System

 B. Access
 (1)  Location Zone
 102 Control Cabin

 C. Prepare for Test
 S 865-065
 (1)  Supply electrical power (Ref 24-22-00/201).
 S 865-001
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：737-300 400 500 AMM 飛機維護手冊 自動飛行 AUTOFLIGHT 2(22)