(3)  
Pitot-static adapters and hoses

 (a)  
Pitot-static adapter - Nav-Aids Ltd. PSS-22300-4-6-6

 (b)  
F72823-40 - Static Adapter

 (c)  
1/4 inch by 50 feet pitot line with appropriate fittings

 (d)  
3/8 inch by 50 feet static line with appropriate fittings

 (4)  
F72786-181, Angle-of-airflow Sensor Calibrator Tool.

 (5)  
Signal Generators (2)

 -HP205, HP201C, HP3311A, HP8111A
 -Wavetek Model No. 171, Model No. 278
 - or Simpson Model 420.

 (6)  
VTVM - FLUKE (Digital)

 C. References
 (1)  AMM 32-00-01/201, Ground Lock Assemblies
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 22-31-00
 ALL  ú ú 08 Page 509 ú Nov 12/99
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
737-300/400/500MAINTENANCE MANUAL
 D. Prepare For The System Test
 S 865-004
 (1)  Do these steps to prepare for the system test:
 (a)  Set the "A" PITOT STATIC HEAT switch (pilots' overhead panel) to OFF to remove the heat from the left angle of airflow (Alpha) vane.
 NOTE: Do not touch the Alpha vane unless you turn the "A"
____ pitot static heat switch off.
 (b)  Connect the radio altitude signal generator.
 NOTE: Set the radio altimeter to zero unless you receive
____
 different instructions.

 (c)  Connect the pitot-static test set to the DADC pitot and static sources.
 NOTE: Keep the ambient pressure unless you receive different
____
 instructions.

 (d)  
Align the airspeed reference bugs with the airspeed pointers (on the Mach/Airspeed indicator).

 WARNING:_______THE HOT ALPHA VANES CAN CAUSE SEVERE BURNS. MAKE SURE THE VANE IS COOL BEFORE YOU TOUCH IT.

 (e)  
Set the left angle-of-airflow sensor vane in a trailing edge up position of 3.0 |1.0 degrees.

 (f)  
Connect a signal generator to each of the engine N1 tach connector.

 NOTE: The polarity of the tach signals does not matter.
____
 (g)  
Remove connector D546 and attach a signal generator to pins 1 and 2.

 (h)  
Set the voltage levels at 10 |3 volts peak to peak at a frequency of 1086 |130 Hz (which simulates 42.0 |5% N1).

 (i)  
Put this data into the CDU to start the FMCS: 1) The outside temperature (OAT) (it is not necessary to do

 this step on airplanes with a TAT probe) 2) The destination elevation (100 Ft) 3) The zero fuel weight (30.0 thousand Kg or 66.0 thousand
 pounds) 4) The reserve fuel weight (5.3 thousand Kg. or 12.0 thousand pounds)
 NOTE:____Use Metric or English units as required. 1 Kg. =
 2.205 pound, 1 pound = 0.4536 Kg.
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 22-31-00
 ALL  ú ú 20 Page 510 ú Nov 12/99
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
737-300/400/500MAINTENANCE MANUAL
 E. Procedure
 S 715-092
 (1)  Do the Operational Test - Autothrottle System.
 NOTE: Do not put the airplane to normal at the end of the test.
____
 S 865-067
 (2)  AIRPLANES WITH A/T COMPUTER P/N 10-62017-1 THRU P/N 10-62017-5; Push LSK 5L (<INTERACTIVE) at the end of the CURRENT STATUS test for the A/T BITE INTERACTIVE TESTS index page.
 NOTE: Make sure that CDU shows "NO FAULT" at the end of the CURRENT
____
 STATUS test.

 S 865-065
 (3)  AIRPLANES WITH A/T COMPUTER P/N 10-62017-11 AND SUBSEQUENT;
 Push LSK 6L (<INDEX) at the end of the CURRENT STATUS test.

 NOTE: Make sure the CDU shows "NO FAULT" at the end of the CURRENT
____
 STATUS test.

 (a)  
Make sure that CDU shows A/T BITE TEST index page 1/2.

 (b)  
Push LSK 4L (<INTERACTIVE) for the A/T BITE INTERACTIVE TESTS index page.
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：737-300 400 500 AMM 飛機維護手冊 自動飛行 AUTOFLIGHT 2(157)